Table of Contents
How do you attach aluminum fascia?
Begin installing aluminum fascia at the center of each length by pushing it up snug to the bottom of the soffit panels. Nail it, then work your way in both directions, driving nails every 16 in., placed about 1 in. from the top and bottom. Overlap joints 1 to 2 in.
What can I use to fasten aluminum fascia?
5) To complete the installation, apply utility trim and fasten aluminum fascia cap with painted aluminum trim nails. If you must face nail fascia, drill holes for trim nails to allow for expansion and reduce denting of aluminum. Face nails are best positioned below the rolled brad in the shadowline.
How do I stop my aluminum fascia from buckling?
To prevent the rake fascia from creeping downhill, the bottom edge of the fascia should be slot punched, then held in place with three or four aluminum trim nails driven into the subfascia. These slots permit the fascia to expand and contract lengthwise without buckling.
What nails do you use for metal fascia?
least 2” roofing nails (or 16d exterior trim nails.) Use 1 ½” roofing nails to install soffit. Use white panel nails to install aluminum fascia. Use tin snips to cut F-channel, vinyl soffit, and aluminum fascia.
Can you staple aluminum fascia?
Slip the panels into the soffit starter and secure to the bottom of the fascia board using 1-inch aluminum trim nails or staples. Secure panels at the grooves so that they maintain a smooth appearance that is flush with the fascia board.
Should you face nail fascia?
Never face nail fascia. Nail every 24″, but do not nail too tight. Nails should penetrate a minimum of 3/4″ into nailing surface.
How is aluminum siding attached?
Vinyl and aluminum siding can be fastened with hammer and nails or by using a power nailer or stapler. For more about the latter, see Power-Nailing & Stapling Vinyl Siding. For vinyl siding, use aluminum, galvanized steel, or other corrosion-resistant nails.
What board do you use for fascia?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
Does aluminum soffit expand and contract?
Why you need a professional soffit installation REMEMBER: if nailed too tightly to supporting boards, aluminum soffits can ripple or bow as they expand and contract with temperature changes.
Does aluminum fascia expand?
Making allowances for aluminum’s unstoppable habit of liberally expanding and contracting with changes in temperature. Securing fascia so it withstands every kind of harsh weather that comes along.
How much do you overlap fascia?
NEVER ‘face nail’ fascia. DO NOT drive nails tight — fascia must be ‘hung’, only snug to soffit, to allow expansion and help prevent distortion. Allow at least 1” overlap of fascia where lengths meet.
Should I screw or nail fascia?
Hometime.com recommends using screws instead of nails when replacing fascia to avoid jarring the existing framing with hammering.
Can you use galvanized nails with aluminum?
These nails have a narrow shank, but a conveniently large head. However, the zinc in galvanized nails reacts chemically with cedar and redwood. Nail manufacturers recommend that you go with aluminum or stainless steel fasteners when you’re using either of these woods—and whenever you’re using pressure-treated wood.
Can you screw aluminum soffit?
You can unscrew the existing soffit, measure, saw and paint a new one out of a sheet of plywood, and screw it back up. You may find it easier though to invest a little more time in installing a lower-maintenance aluminum or vinyl soffit that won’t require painting or short-term replacement.
What screws to use for soffit?
Hillman #6 x 3/8-in Phillips-Drive Sheet Metal Screws (1000-Count Use for soffit, gutter and trim installation or repair. Color matched for white soffit and trim.
What kind of screws should I use for soffit?
Round head screws designed for installing soffits and gutters.
Should drip edge be nailed to fascia?
A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.
Is drip edge nailed to fascia?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Is aluminum siding hard to install?
Installing aluminum siding may be the most eye-catching home improvement that you can make. The change can be remarkable, and is sure to turn heads and impress your neighbors. With a little know-how and a few simple pieces of equipment, this is a task that you can easily accomplish yourself.
How do you secure aluminum siding to a house?
Purchase galvanized steel or aluminum roofing nails with a head at least 3/8 inch in size. Drive new nails into the center of the slots on the siding nail hem. Snap the bottom edge of the piece of siding into top locking ridge over the nail hem.
What is under my aluminum siding?
Often, you’ll find 1/2″ styrofoam or other rigid insulation underneath the aluminum siding which was nailed into the siding with fat headed roofing nails. Removing this stuff is simple since it is so fragile and can be torn away from the building simply.
