Table of Contents
How do you install a subwoofer and amp in a factory system?
Usually, you’ll be installing a 4-channel amplifier with speaker-level inputs. The best way to connect it to a factory system is to tap into the stereo’s speaker outputs for the amp’s input signal. Then send the amp’s outputs back to the stereo’s harness, and on to the speakers through the factory wiring.
Will a sub work without an amp?
In nearly all cases, the answer is yes. Unless you have a system in your car or boat that is already powering a subwoofer, you’ll need to find an amplifier that will power your sub. Your head unit will typically provide a low-power signal (RCA output) that can be used for an amplifier to power your subwoofer.
Where do you put subwoofers in your car?
In the Blue Corner: The Trunk. Without a doubt, the most popular placement for a car subwoofer is the trunk. It’s the place where you most likely thought of housing your subwoofer when you first decided to invest in one.
Can I install a subwoofer with a stock radio?
…it takes amplified speaker level signals and converts them into high quality preamp signals that can be fed into an amplifier. So now you know – it’s definitely possible to install a subwoofer and amplifier to your factory system, and still have it sounding good.
How do I hook up subs to a factory stereo?
8 Steps To Install A Subwoofer To A Factory Stereo Step 01 : Gather all necessary equipment. Step 02 : Choose a speaker and an amp. Step 03 : Remove the battery from the vehicle. Step 04 : Disconnect the wires of the speaker. Step 05 : Identify the relevant connections. Step 06 : Run wires. Step 07 : Reinforce the connections.
Can I just add a subwoofer to my car?
And it’s actually quite easy, thanks to simple subwoofer upgrades from the aftermarket that can be added to almost any existing car stereo system. Adding a subwoofer to your audio system generally means also having to purchase and install an amplifier to power it.
What is the difference between an amplifier and a subwoofer?
In computer speakers, the amplifiers are contained inside the speakers themselves. Amplifiers are also often contained inside subwoofers. This might be the cause of your confusion. Subwoofers are large woofers that only reproduce very low sounds, such as that from bass guitars.
Can a subwoofer be used as a speaker?
Subwoofers are designed for low-frequency audio signal emissions including their structural design, included components, and available input or output ports. Subs cannot be used as speakers because they do not have the capacity to stream high-frequency audio signals required by other speakers.
Do subwoofers drain car battery?
Subwoofers Can Drain Car Battery Your car battery can get drained when it sends more power than it receives from an alternator. Generally, subwoofers and their amplifiers draw relatively more current than the normal car stereo system. That’s because more power is required to play bass frequencies by a subwoofer.
How do I hook up an amp without RCA cables?
There are almost three methods available to hook up your amplifier without using any RCA jacks.3 Ways To Hook Up Amp Without RCA Jacks Connect Speaker Wire To RCA Adapter. Install Using High-Level Amp Inputs. Hook-Up Amp Using Line Output Converter(LOC).
Is a line out converter necessary?
A: Yes, definitely. Amplifiers that offer speaker-level inputs don’t require a separate line output converter to tap into existing speaker wires to get their signal. This amp includes an adapter that lets you connect your speaker wires directly, without needing a line output converter.
How do I tap my rear speakers into subs?
Some (many) powered subs have high level inputs, so you can just tap into the rear speaker wires. If your car has a factory sub, use its speaker wire instead. If it doesn’t have high level inputs, you can use a basic line out converter that ties into the speaker wires and turns them into a rca output.
Can I use factory amp and aftermarket amp?
There is not a good way to tie in the factory amp IMO. The stock radio only provides a left/right signal and balance to the amp. Rear speakers and sub signal as well as fade are created in the amp. Best bet is to bypass all of that and run an aftermarket amp/amps.
Should I bypass my factory amp?
Bypassing the factory amp takes a little more work because you have to run the bypass harness to the factory amp, which is often located in some other part of the car. It’s usually worth the extra effort because you’ll get better sound from your new stereo, even if you’re keeping those factory speakers.
Can you install an amp without RCA jacks?
The first, easy method you can use to connect your amp is through an RCA adapter for car stereo. Whether you own an old head unit without RCA jacks, you can still add an amplifier to your car and give your speakers some extra juice. You need two RCA plugs, an adapter cable, and of course, some speaker wires.
How much does it cost to get a subwoofer installed?
For subwoofer installation, parts typically cost $20–$300, but will vary. Any additional charges will be assessed after the installation is complete.
