Table of Contents
Do you need an amp to install a subwoofer?
Subwoofers are designed to increase the bass frequencies, resulting in a deep, thumping sound. In most cases, they are paired with an amplifier to boost the sound. If you do not have the funds for both components, you can still hook up a subwoofer without an amplifier; it simply involves a little more know-how.
How do you install a subwoofer and amp in a factory system?
Usually, you’ll be installing a 4-channel amplifier with speaker-level inputs. The best way to connect it to a factory system is to tap into the stereo’s speaker outputs for the amp’s input signal. Then send the amp’s outputs back to the stereo’s harness, and on to the speakers through the factory wiring.
Can I install a subwoofer with a stock radio?
…it takes amplified speaker level signals and converts them into high quality preamp signals that can be fed into an amplifier. So now you know – it’s definitely possible to install a subwoofer and amplifier to your factory system, and still have it sounding good.
Do subwoofers need power?
A subwoofer (sub) is speaker, that is dedicated to the reproduction of low-pitched audio frequencies most commonly referred to as bass. Passive Sub: Passive subs are called passive because they need to be powered by an external amplifier or Audio/Video (A/V) receiver . This is similar to traditional speakers.
Is a line out converter necessary?
A: Yes, definitely. Amplifiers that offer speaker-level inputs don’t require a separate line output converter to tap into existing speaker wires to get their signal. This amp includes an adapter that lets you connect your speaker wires directly, without needing a line output converter.
How do I tap my rear speakers into subs?
Some (many) powered subs have high level inputs, so you can just tap into the rear speaker wires. If your car has a factory sub, use its speaker wire instead. If it doesn’t have high level inputs, you can use a basic line out converter that ties into the speaker wires and turns them into a rca output.
How do I hook up subs to a factory stereo?
8 Steps To Install A Subwoofer To A Factory Stereo Step 01 : Gather all necessary equipment. Step 02 : Choose a speaker and an amp. Step 03 : Remove the battery from the vehicle. Step 04 : Disconnect the wires of the speaker. Step 05 : Identify the relevant connections. Step 06 : Run wires. Step 07 : Reinforce the connections.
Can you hook up an amp without RCA cables?
To connect your amp without RCA jacks, you can also use the high-level input amp. The high-level inputs at the back of the amplifier allow you to feed signals into the factory speaker wires. The name “high-level input” comes from the fact that these ports deliver a higher voltage than a standard preamp output.
Can I just add a subwoofer to my car?
And it’s actually quite easy, thanks to simple subwoofer upgrades from the aftermarket that can be added to almost any existing car stereo system. Adding a subwoofer to your audio system generally means also having to purchase and install an amplifier to power it.
Can you hook up a car subwoofer to a home stereo?
You can hook up a car subwoofer to a home stereo directly if: You have a subwoofer or more than one subwoofer that can be wired for at least 8 ohms total. This can be two 4 ohm subwoofers or a 4 ohm dual voice coil (DVC) subwoofer.
What do you need to set up a subwoofer?
Subwoofers require a lot of power, so they have to be wired to both a power source, like a car’s battery, and an amplifier. After connecting them to the stereo speakers, run a separate wire to a ground source, such as an exposed metal bolt, for safety.
Can a subwoofer be used as a speaker?
Subwoofers are designed for low-frequency audio signal emissions including their structural design, included components, and available input or output ports. Subs cannot be used as speakers because they do not have the capacity to stream high-frequency audio signals required by other speakers.
Where should I place a subwoofer?
Placing a subwoofer in the corner of a room can increase its output, making it sound louder. The great thing about a subwoofer (especially a wireless subwoofer) is it can be situated almost anywhere on your floor space. There is no formula for locating the best spot. And, it’s truly your personal preference.
Do RCA cables go to input or output on amp?
RCA cables and speaker wire. Amp wiring kits often don’t include signal wiring. Your amplifier gets its input signals from the receiver’s output typically via RCA cables. RCA cables come in stereo pairs, in various lengths.
Can you connect LOC to rear speakers?
If you’re installing the LOC behind the radio, all the speaker wires are right there, including power and ground. However, if your car has rear deck speakers, you could install the LOC in the trunk and get the speaker inputs from the back deck speakers. Then just run your remote wire and RCA’s from the dash to the amp.
