Table of Contents
Do you put drywall behind a shower surround?
Fiberglass and acrylic tub and shower enclosures come with a flanged edge that attaches directly to the wall studs, and the proper way to hide this flange is to install drywall over it. Consequently, enclosures are typically installed on the bare studs.
Do I tile before fitting shower enclosure?
We always advise fitting the shower tray before tiling the walls or installing wall panels as this ensures a more watertight seal around the sides of the tray. Initially, it may be easier to get the tray level by adjusting the key corner legs first.
Can you install shower walls over drywall?
The short answer to the question is, “It’s not recommended.” However, this answer only really only suffices if you’re converting a room that was never a bathroom into a wet space. Drywall on its own is not suitable for use in bathrooms because it is prone to absorbing moisture and thus losing structural integrity.
Should you put plastic behind shower walls?
They are required beneath your shower pan and behind your shower walls. Moisture barriers can be made of polyethylene or a membrane that is rolled directly onto the drywall. No matter what they are made of, without them, your shower is subject to moisture damage.
Do you put insulation behind shower walls?
Insulating behind shower walls improves moisture control, which in turn reduces the chances of mold growth. Apart from retaining heat and minimizing condensation, insulating behind shower walls also provides better acoustics by reducing annoying sounds from outdoors or between rooms.
What type of drywall goes behind a shower?
Look into cement board if you need waterproof drywall. This type of waterproof drywall is designed for wet areas such as showers and bathtub surrounds. Be cognizant that cement board requires a moisture barrier behind it, which makes the installation process longer than moisture-resistant drywall.
What goes first shower pan or walls?
Whether you choose to install tile or the panel walls, drywall always goes on top of the shower pan, after the pan is set into the floor. Both tile and shower walls perform the same function, they just do so with different types of materials.
Which wall do you tile first in a shower?
Always tile the back wall first in a shower/tub so that you can hide the grout joints on the sides.
Can you lay shower tray on floorboards?
When learning how to lay a shower tray on a wooden floor, you will need to mark the area where the tray will stand. Next, replace the floorboards within that area with a minimum of 18mm marine ply. You will need to ensure there is access to the waste pipes in the floor beside the tray.
How do you waterproof drywall above a shower?
Prime the drywall with oil- or shellac-based primer. These coatings protect against moisture better than water-based primer, but they are noxious, so wear a respirator while using them. Spread the primer with a paintbrush or roller and let it dry before painting.
Do you caulk a 3 piece shower surround?
2 Answers. You probably don’t need to, as the lap in the surround design will drain water effectively. However, those are traps for mildew and grime. I’d clean them as deeply as you reasonably can with rubbing alcohol, then put in a bead of 100% white silicone.
How do you remove a shower wall surround?
Starting at the top outside corner, tap the putty knife behind one of the corner panels and pry out the corner. Keep tapping the putty knife deeper until you can grasp the edge of the panel with your fingers or with pliers. Keep tapping and pulling until the panel comes off and then move on to the other corner panel.
How do you install a shower surround over existing tile?
How to Install a Shower Surround Over Existing Tiles Step 1: Remove Plumbing Fixtures. Step 2: Rough Up Tile Surface. Step 3: Cut and Install Apron-Trim Pieces. Step 4: Level Vertical Apron-Trim Piece. Step 5: Install Back Panel. Step 6: Apply Sealant and Position Panel. Step 7: Position Side Panel.
How hard is it to replace a tub surround?
The enclosure around a bathtub often gets more wear than the tub itself. It’s not uncommon to be faced with major wall repair long before the tub is ready for replacement. This can a pretty difficult job if you have ceramic tile walls, and installing a new system of tub surround panels is usually an easier solution.
How do you frame a shower wall?
The basic rules of framing apply to shower walls in regard to spacing. Wall studs should be 16 inches apart from each other, measuring center to center. In some remodel jobs, you’ll come across non-load-bearing walls that have as much as 24 inches between them.
How far should shower valve stick out from wall?
wall position, including tile (2-1/16″ [52mm]). The center line of the supply and discharge piping should be a maximum of 2-3/16″ (56mm) and a minimum of 1-7/16″ (37mm) behind the finished wall surface.
What goes behind shower panels?
Install cement board behind tub and shower enclosures. Install cement board or an equivalent moisture-resistant backing material on walls behind tub and shower enclosures composed of tile or panel assemblies with caulked joints.
Do you install backer board before shower pan?
It requires no mud job or waterproofing membrane, but it does require direct access to the studs of the shower. This will create a small lip at the bottom of the shower walls where tiles or an acrylic surround would bump out, leaving a gap. Therefore, the pan must be installed first.
