Table of Contents
How are mantels attached to the wall?
Since neither option is very sturdy, we recommend you attach the mantel to a cleat—a simple piece of lumber securely fastened to the wall. One cleat runs horizontally under the mantel shelf, and the others run vertically inside the legs (most mantels are hollow in back).
How do you hang a heavy mantle on drywall?
Holding your drill at a 45 degree angle downward, drill a pilot hole through the shelf and drywall and into the stud. Install a finishing nail into each of the pilot holes with a nail gun or hammer; the nails must be long enough to penetrate at least 1 inch into the drywall. These nails will secure the mantle in place.
How do you secure a floating mantel?
Make sure those marks are level, centered and extend far enough to cover the mantel’s length. drill holes at each mark. Drill Sleeve Holes. Drill holes at each mark using a drill and 3/4″ masonry bit. insert lead sleeves into holes. Insert Sleeves. drive lag bolts. Drive Lag Bolts. install the mantle. Install Mantel.
How do you attach wood beams to drywall?
Covering the Beam Screw drywall to a wooden beam on the three exposed sides to cover them, using type W drywall screws, also called “coarse thread” screws. Add joint compound, commonly called “mud” in the drywall trade, at the inside and outside corners.
How do you attach a fireplace mantel to the wall?
Mount the fireplace mantel. Push the mantel against the wall, using the drawn lines. The mantel should fit around the cleats, which hold it in position. Then use the drill to insert screws through the mantel and into the cleats. These screws should be roughly 16 inches apart.
How do you install a floating mantel on a brick fireplace?
How to Install a Mantel Remove the old mantel. Add support by drilling holes for lag shields, then install lag bolts into the brick. Measure carefully and drill corresponding holes for the wood mantel. Push the wooden mantel carefully into place using wood glue for extra support.
How do you attach a floating mantel to a brick fireplace?
Slide Over Bolts Method Locate the studs behind the brick, stone, or faux veneer. Drive 1/2in lag screws through each of the studs. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. Apply construction adhesive into the holes. Slide into place, admire, and enjoy!.
Can you drill into shiplap?
I hadn’t yet drilled into these carefully installed shiplap boards, not one of them. They were totally flawless. To make sure I wasn’t hitting a stud, I used a small drill bit to predrill holes, clearly being able to feel if the bit popped through into nothing or wanted to bite into something chewy and rough.
What type of wood is used for mantels?
Walnut is a popular choice for fireplace mantels. It is a harder and heavier type of wood than most and is extremely durable. The rich dark brown wood is an excellent for an impressive fireplace mantel. Hickory is also a great choice for a fireplace mantel if you are going for a unique look.
What holds up a fireplace mantel?
A fireplace mantel spans the top of a firebox and is often supported by legs; generally the deepest and heaviest section of the fireplace. It can also be floating, supported by corbels, and can appear well above the firebox opening or right in line with the opening.
Do you install mantel before or after stone?
It’s best to build the mantel right into the stone, rather than refinishing the fireplace first.
How thick should a fireplace mantel be?
A depth of 7 inches is ideal for most mantels, as it allows plenty of room to accommodate decorative objects. Keep in mind that the top and the sides of the mantel should be the same depth.
How do you anchor a heavy mantle?
The mantel needs to anchor to the studs in the wall above the fireplace. Drive 1/2- or 3/4-inch rebar rods or lag screws into pilot holes drilled into the studs. For best support, drive them all the way through the stud. Place one rod or screw in each stud behind the mantel.
What is a floating mantel?
Our mantels are hollow on the inside, providing an easy alternative to solid wood mantels. Live grain end caps maintain the look of a solid piece of wood. Each mantel is hand crafted from reclaimed longleaf pine, providing a unique look and character that cannot be duplicated.
How do you attach wood to drywall?
Apply a bead of construction adhesive on the back of your wood installation, making sure to trace along the edge. Apply some additional construction adhesive to the center of the wood’s back. Press the wood firmly to the drywall. Wipe any excess adhesive off the wall with a damp rag.
How are fireplace mantels attached?
As with many other forms of mantle or shelf, a fireplace mantel can be commonly attached to the wall with screws or lag bolts. Bolts are screwed into the wall above the fireplace before a mantel is slotted straight onto it.
What are geocast beams made of?
Geocast Beams are made from moulded ceramic and are heat proof making them suitable for use with solid fuel stoves. They come in two colours; light and dark oak and have a realistic finish making it difficult to distinguish them from real oak.
How do you attach a mantel to brick?
Lift the mantel and position it in place, aligning the holes in the back of the mantel with the support rods. Push the mantel onto the rods until the back of the mantle is against the bricks. Gently tap with a small hammer and a small piece of wood if necessary to completely align the mantel next to the brick.
What is the best way to drill into brick?
Begin by drilling a pilot hole using a small masonry bit. Then, attach the larger bit and drill again to make a bigger hole. Make sure the drill is perpendicular to the brick wall. Drilling through brick and mortar places stress on the drill, causing it to heat up.
