Table of Contents
Where should closet rod brackets be placed?
Before installing a closet rod, it is best to place closet brackets in a position on the wall that allows for the most support. This will require a stud finder. Once wall studs have been located, closet rods and brackets can be screwed into the stud for optimal support.
How far should closet rod be from shelf?
A minimum of 10 inches is best, but it’ll depend on the size of your hangers. If there is a shelf above the rod, determine the vertical distance from the rod to the shelf; two inches should be suffice.
How do you support closet shelves?
If additional support is needed to keep the shelves from sagging, either install a metal bracket in the center under each shelf, or glue and nail a piece of 1 x 2 to the front edge of each shelf.
How do you support a closet shelf?
Make sure that each shelf support is level. Attach each side support to the side walls of the closet at the appropriate height by nailing them into the studs. If you are building simple shelves rather than cubbies, you also need to add a long shelf support along the back wall of the closet.
How high should the top shelf be in a closet?
Ideally, the top shelf of a closet is high enough to tuck items out of the way, but low enough that you can retrieve them without a stool. The recommended shelf height is between 87 and 96 inches from the floor. The shelf should also sit at least a foot away from the closet ceiling.
How do you hang a closet rod from the ceiling?
Draw a straight line on the ceiling at right angles to the joists using a yardstick or straightedge tool as your guide. Make the line the length of the closet rod you purchased for the project. Put the line at least 12 inches from the back wall of the closet to allow room to hang clothes hangers on the clothes rod.
How do you secure a closet rod?
Attach closet rod support brackets at various points along the closet rod. Use a stud finder to locate the studs in either the wall or ceiling. Drill pilot holes, using a drill and drill bit. Alternatively, use self-tapping wood screws and mount the bracket directly into the stud.
How long can closet rods go without support?
If your closet rod is longer than 48 inches, you will need support. However, regardless of how long the closet rod is, if you’re hanging heavier items such as winter jackets, then you will want support no matter what.
How much weight can a wooden closet rod hold?
Never put more than 25-pounds of clothing on one of these rods or it will fail. The motorized version works with a remote control and can hold up to 60-pounds of clothing per rod.
What screws to use for closet shelves?
Yes you need to use screws. I would use 2 1/2-3″ deck screws. You need to go through 3/4″ of wood and 1/2″ of sheetrock, then into the stud at least as far. Your shelves will bow unless you put a center support.
Can you hang closet rod with drywall anchors?
To securely install a closet rod in drywall: Drive screws into the wall stud or drywall anchor, securing the bracket in place. Repeat this process for additional brackets, making sure they are level with the first bracket. Set your closet rod in place and use it to hang your clothing.
Do closet rods need to be in studs?
Basic Installation It should be placed in front of a stud so you can screw into the stud to give it support. The typical height of a closet rod is from 60 to 80 inches, and both brackets should be at the same height, or the hooks you hang from the rod will slide to one end.
How thick is a closet rod?
A closet-rod dowel is usually between 1 1/4 inches to 1 3/8 inches in diameter. This diameter allows for plenty of hanging strength. It resists breakage, and will not bend when properly supported.
How thick should closet shelves be?
The minimum thickness you need for shelves is 1/2 inch, but if you plan to load them with heavy items, use 3/4-inch plywood.
How wide should a shelf be?
Shelf depth is determined by the size of the items to be stored, generally within the range of 6 to 24 inches. Shelf depth for a general purpose bookshelf is usually 10 to 12 inches. Shelf spacing will generally range from 7 to 15 inches with 8 to 12 inches being common for bookshelves.
How do you maximize a hanging space in a closet?
If most of your clothes are short hanging, add an extra closet rod to instantly double the amount of hanging space. Add-on, cascading and slim profile hangers are other good ways to save space. Finally, give yourself the benefit of drawers in your closet by using hanging sweater and hanging shoe organizers.
How many brackets do I need for closet rod?
Adjustable Closet Rod 1 TM Page 5 TM NOTE: Recommended 16″ bracket spacing. Maximum 32″ bracket spacing. First, measure the width of your closet. Measure 11-1/2″ from the rear closet wall.
Is a metal or wood closet rod better?
Wood rods use a shelf support and a hook for the rod. Metal rods are integral to the shelf and are supported with various wall anchors. When supporting these, you will get more support and stability when you install into the studs, regardless of whether the rod is made of wood or metal.
How much weight can the shelf in my closet hold?
For their closet shelving, you can typically expect to hold around 35 pounds per linear foot, unless you get the shelving with the ShelfTrack Hardware. Then, you can hold a very respectable 75 pounds per linear foot. If you get their Maximum Load Standard Shelving, you can expect to carry up to 600 pounds per unit.
How much weight can Rubbermaid shelving hold?
Total Weight Capacity: 350 lbs.
What can I use instead of a closet rod?
Closet rods. Closet Organizer. Closet rod systems are an easy and relatively affordable alternative to a traditional closet. Wardrobe/ Armoire. Revere Armoire. Under-the-bed Storage. Foldable Divider Organizers. Floating Shelves. Floating Wall Shelves. “Headboard” closet. Cubicle Organizer.
