Table of Contents
How do you hang a shelf and rod in a closet?
How far should closet rod be from shelf?
A minimum of 10 inches is best, but it’ll depend on the size of your hangers. If there is a shelf above the rod, determine the vertical distance from the rod to the shelf; two inches should be suffice.
Where should closet rod brackets be placed?
Before installing a closet rod, it is best to place closet brackets in a position on the wall that allows for the most support. This will require a stud finder. Once wall studs have been located, closet rods and brackets can be screwed into the stud for optimal support.
How long can closet rods go without support?
If your closet rod is longer than 48 inches, you will need support. However, regardless of how long the closet rod is, if you’re hanging heavier items such as winter jackets, then you will want support no matter what.
How much weight can a wooden closet rod hold?
Never put more than 25-pounds of clothing on one of these rods or it will fail. The motorized version works with a remote control and can hold up to 60-pounds of clothing per rod.
How do you hang a closet rod on drywall?
To securely install a closet rod in drywall: Measure the size of the space where the closet rod will go. Buy a closet dowel rod and cut it to length. Choose a wall bracket that can be positioned so that you can screw it into wall studs. Mark the place where your first bracket will be installed. Drill pilot holes.
What is standard shelf height?
For ease of shelf access, bookcases are generally no higher than 84 inches. Small bookcases are usually 30 to 42 inches high. The highest shelf in a bookcase should be as high as an average-sized person can comfortably reach – about 72 to 78 inches.Contact Us. Species Modulus of Elasticity (E) Western Red Cedar 1.12.
Does a closet rod have to be in a stud?
Basic Installation It should be placed in front of a stud so you can screw into the stud to give it support. The typical height of a closet rod is from 60 to 80 inches, and both brackets should be at the same height, or the hooks you hang from the rod will slide to one end.
What screws to use for closet shelves?
Yes you need to use screws. I would use 2 1/2-3″ deck screws. You need to go through 3/4″ of wood and 1/2″ of sheetrock, then into the stud at least as far. Your shelves will bow unless you put a center support.
How many brackets do I need for closet rod?
Adjustable Closet Rod 1 TM Page 5 TM NOTE: Recommended 16″ bracket spacing. Maximum 32″ bracket spacing. First, measure the width of your closet. Measure 11-1/2″ from the rear closet wall.
How deep is a closet shelf?
Closet shelves are NOT one size fits all. Ideally, they should be a variety of depths based on what each section needs to store. Builders commonly put in shelving that is 11 ¼” deep.
How thick should a closet rod be?
A closet-rod dowel is usually between 1 1/4 inches to 1 3/8 inches in diameter. This diameter allows for plenty of hanging strength. It resists breakage, and will not bend when properly supported.
How much weight can the shelf in my closet hold?
For their closet shelving, you can typically expect to hold around 35 pounds per linear foot, unless you get the shelving with the ShelfTrack Hardware. Then, you can hold a very respectable 75 pounds per linear foot. If you get their Maximum Load Standard Shelving, you can expect to carry up to 600 pounds per unit.
How much weight can Rubbermaid shelving hold?
Total Weight Capacity: 350 lbs.
How do you secure a closet rod?
Attach closet rod support brackets at various points along the closet rod. Use a stud finder to locate the studs in either the wall or ceiling. Drill pilot holes, using a drill and drill bit. Alternatively, use self-tapping wood screws and mount the bracket directly into the stud.
What is a good shelf depth?
The shelves shouldn’t be too deep. The standard depth of most shelves is 16 to 20 inches deep. The highest shelf should be shallower, like 12 inches deep, to make those items easier to access. If you find that stuff seems to get pushed to the back and forgotten about, you should consider even shallower shelves.
How deep should built in shelves be?
Most shelves are built a minimum of 11 to 12 inches deep, but this is your chance to customize: Go for it!.
How much gap should be between shelves?
The rule of thumb for spacing is 12 inches between each shelf but bump that up to 15 or 18 inches and you enhance that sense of exposure and accessibility. Length is where you’ll see the most variation.
How do you secure a shelf to a wall without screws?
You can use plastic ties, steel cables, or Velcro straps to accomplish. Please note, you may have to drill or glue hardware to the back of the furniture. Be aware this method may not be sufficient for holding up furniture to the wall in the event of jostling, a natural disaster, or if the furniture is top-heavy.
How do you anchor a drywall shelf?
How to Use A Drywall Anchor Place the anchor in the pilot hole and tap it into the wall until the anchor is completely inserted. You’ll have to drill a larger pilot hole for toggle bolts and steel hollow wall anchors. Once the anchor is inserted, use a screwdriver to drive the screw securely into the anchor.
Can you screw into drywall without an anchor?
The threads of a screw into only drywall, without an anchor, will NOT permanently hold in the drywall. It will just pull right back out sooner or later. Even though it may screw into the drywall and “feel” tight, when you hang a picture on it, it will pull out almost immediately. Especially if the picture is heavy.
