Table of Contents
Where do you start tile tub surround?
For a tub surround only, install the backerboard and tile 12 inches above the tub. When tiling around a tub, mark the first layout line at the vertical edge of the tile next to the tub. Follow the order shown in the diagram to snap the rest of the lines. If the tub is level, start with a full tile at its rim.
How do you prepare a tub surround for tile?
Tub or shower wall tile preparation: Apply a layer of 1/2″ thick cement backer board to the wall studs. Tape any seams and corners with fiberglass tape. Apply thin-set adhesive over the fiberglass tape, and allow it to dry. Roll a waterproofing sealer over the walls, and allow the sealer to dry.
Which wall do you tile first in a tub surround?
Always tile the back wall first in a shower/tub so that you can hide the grout joints on the sides.
Do you tile over tub lip?
Tiling around a tub with a lip means that you need to place the cement board above it. You will install the tiles against the cement board, leaving the lip unexposed with a gap between it and the board. Secure the bottom row of tiles to the tub away from the lip with silicone caulk.
When tiling a shower where do you start?
Start out level Start tile on a level board. Screw a straight board to the level line and stack tile on the board. Close-up of improper spacing. Don’t start on the edge of the tub or shower. Don’t start the first row of tile by resting it against the tub or shower.
Do you tile before or after drop in tub?
In your installation process, you should put the backer board down and tile the floor and the backsplash around the tub first, but leave off the row of tiles that directly surround the tub. Next, you’ll install the tub, make it level, and connect all of the plumbing.
What do I put behind tile in a shower?
Install cement board or an equivalent moisture-resistant backing material on walls behind tub and shower enclosures composed of tile or panel assemblies with caulked joints. Don’t use paper-faced backer board, i.e., paper-faced drywall, behind seamed tub and shower enclosures.
What do you put on shower walls before tile?
Whenever installing tile in any area of your house, you need a special substrate, or base layer. In showers, the standard substrate is tile backer, also called cement board or cement backer board.
Where do you start when tiling a wall?
It’s always advisable to start tiling your grid in the centre of the wall, as it’s easier to make sure your pattern is symmetrical. It also means any half-tiles you may need can go at the end of each row and will be of matching size.
Should you tile shower niche first?
This ensures any splashing or accidental spraying of water on the wall or shower door does not result in any seepage and water damage behind the tiles. If the niche needs to be tiled, then it has to be done tile by tile.
How do you install tile over a shower surround?
How to Attach Tile to Drywall Above a Shower Surround Step 1: Create a Template. Step 2: Lay Out Your Tile Pattern. Step 3: Cut Edge Tiles. Step 4: Create Chalk Lines. Step 5: Apply Tile Glue. Step 6: Attach the Tiles. Step 7: Make Additional Chalk Lines. Step 8: Finish Attaching Tiles.
Do you grout between tile and tub?
Grout or Caulk Between Floor Tile and Tub: Which Is Better? Since you are joining two different materials together, you should use caulk in the space where the floor tile and tub meet. Grout is not flexible, so it’s not the best material for the job, while caulk allows for movement and also provides a better sealant.
How do you fill gap between tub and floor?
If your gap is smaller than 1/8 inch in width, use regular caulk; fill gaps larger than 1/8 inch with a sanded caulk. Make sure the gap is clean and dry, then squeeze a thin, even bead of caulk into the space. To get the best coverage, cut the tip of the caulk tube so the bead that emerges completely fills the gap.
How do you fill a large gap between tile and wall?
Answer: A single bead of caulk can fill a gap of ¼ inch. If the gap is greater than that, then simply apply to the deeper areas. Then, wait for your caulk to dry. Next, apply another layer of caulk.
Do you put backer board over tub flange?
ANSWER – No there should not be a gap between the top of the bathtub flange and the backer board on the wall. The backer board should overlap the tub flange so the tile has a stable backing to attach to. This requires shimming the backer board out from the studs so the wall is plumb.
Do you drywall over the tub flange?
You can bring sheetrock right down to the flange just like in the picture as long as you aren’t going to tile over it. I would suggest using sheetrock over backer board on surfaces which you intend to paint.
Does tub go in before flooring?
So you are installing a new bathroom and suddenly have hit a snag-which should you install first, the flooring or bathtub? The short answer is that standard bathtubs such as alcove and corner bathtubs should always be installed first, followed by the wallboard, the subfloor and the vinyl.
Does flooring go under tub?
Bathroom floors are notorious for suffering water damage and the area under the bathtub is no exception. Flooring repairs can be intimidating, but the subfloor under the tub generally consists of plywood secured over floor joists and is fairly simple to replace — once you get access to it.
Do you tile under a shower tray?
We always advise fitting the shower tray before tiling the walls or installing wall panels as this ensures a more watertight seal around the sides of the tray. Initially, it may be easier to get the tray level by adjusting the key corner legs first.
