Table of Contents
Can you hook up an amp and subs to a stock stereo?
…it takes amplified speaker level signals and converts them into high quality preamp signals that can be fed into an amplifier. So now you know – it’s definitely possible to install a subwoofer and amplifier to your factory system, and still have it sounding good.
How do you hook up two amps in a car?
The best way to wire multiple amps to a single power cable is to use a power distribution block. That allows you to use a single cable for most of the run, including the crucial portion that passes through the firewall and then to use shorter individual cables to actually connect to each amplifier.
Is a subwoofer cable just an RCA cable?
you can use a standard RCA cable, but a subwoofer cable is suggested as it has more shield in it and provides more clarity and resolution. a subwoofer cable comes with a standard RCA connector but is thicker than the standard RCA cable.
What should my LPF be set at?
As a general rule, the Low-Pass Filter should be set at a value approximately equal to (or below) 70% of your main speaker’s lowest frequency response. For example, your speaker’s frequency response goes down to 43Hz. 70% of 43Hz equals 30.1, so you should set the subwoofer’s low pass filter to 30Hz.
How do you hook up a subwoofer to a stereo?
Connect. If you are using your subwoofer with a home theater receiver, the connection is simple: Just run an audio interconnect cable like this one from the receiver’s subwoofer output to the subwoofer’s line input (pictured above). If the subwoofer has an input labeled LFE, use that one.
Where do you put subwoofers in your car?
In the Blue Corner: The Trunk. Without a doubt, the most popular placement for a car subwoofer is the trunk. It’s the place where you most likely thought of housing your subwoofer when you first decided to invest in one.
How do you hook up an amp to a factory radio?
Usually, you’ll be installing a 4-channel amplifier with speaker-level inputs. The best way to connect it to a factory system is to tap into the stereo’s speaker outputs for the amp’s input signal. Then send the amp’s outputs back to the stereo’s harness, and on to the speakers through the factory wiring.
Can you install an amp without RCA jacks?
The first, easy method you can use to connect your amp is through an RCA adapter for car stereo. Whether you own an old head unit without RCA jacks, you can still add an amplifier to your car and give your speakers some extra juice. You need two RCA plugs, an adapter cable, and of course, some speaker wires.
Is a line out converter necessary?
A: Yes, definitely. Amplifiers that offer speaker-level inputs don’t require a separate line output converter to tap into existing speaker wires to get their signal. This amp includes an adapter that lets you connect your speaker wires directly, without needing a line output converter.
Can I hook up 2 amps to 1 sub?
Can I connect two amps to one sub? A single voice coil sub won’t work with the two amps and will result in the outputs being fried as soon as you turn it on. A dual voice sub and the same amps can be done, but it needs to be effectively balanced. However, two amps one sub is definitely possible.
How do you hook up two amps to a stereo?
The simplest way to set up a dual-amp stereo rig is to use two amps of the same make and model, in either a combo or head-and-cab arrangement. Use an effect pedal or tuner with stereo outputs, or a dedicated ABY box, to split the guitar signal into two, sending each signal to its own amplifier.
How do I connect two amps to one RCA?
How To Split RCA For Multiple Amps Unplug all the RCA connections going into the first amp. Next, plug the white RCA into the female end of one splitter and do the same for the red RCA but on a different female socket of a separate splitter. Hook the first set of RCAs from the first splitter into the first amp.
Is a capacitor needed for subs?
Voltage Stability Capacitors offer some small amount of protection for amplifiers from potentially damaging under-voltage surges over time if you play loud music regularly. But most of the reason for adding capacitors is to keep your car voltage stable.
What should I set my LPF subwoofer to?
A good rule of thumb for a home stereo subwoofer low pass filter (LPF) setting is 70 to 80Hz. Once you’ve set it, adjust slowly and listen for what sounds the best to you.
What should I set my HPF and LPF to?
You usually set the HPF with a steep slope say 24db/octave because you are trying to protect the sub from damage and a 12-18db/octave on the LPF because you want it to kinda “blend” in with your mids. The steeper the slope (db/octave) the less your sub will creep into the neighboring frequencies.
