Table of Contents
What do you need to Hydro dip with film?
Step 1 — Cut out a piece of film. Roll out the sheet of film and lay your object on top. Step 2 — Apply masking tape to film. Now apply strips of masking tape to opposite sides of the film. Step 3 — Float film on water. Step 4 — Spray film with activator. Step 5 — Dip thing. Step 6 — Cleanup.
How do you activate hydro dip film?
Spray the activator from side to side holding the gun approximately 12-18” from the surface in an overlapping pattern as typically done when laying down a consistent path of activator with other films. The speed this is done will determine the amount of activator being deposited.
How long does it take for hydro dip film to dry?
The clear coat should be allowed to dry for at least 8-24 hours. Your item will be ready to use when the clear coat is no longer tacky to the touch and has sufficient time to fully cure out.
Do you need activator for hydro dipping?
Under and over activating are two of the leading causes in problems with hydro dipping. You are not applying a layer of paint, you just need enough activator (with a fine mist, fan pattern spray) to cover the film lightly.
Can you hydro dip without spray paint?
However, you’ll need to be more careful using the spray can because spraying too close can form air bubbles on the surface, leading to undesirable patterns. People would often ask, can you hydro dip without spray paint? Yes, you can.
What supplies do I need to hydro dip?
Step-By-Step Guide to Hydro Dipping Large, deep plastic container (the container will have paint on the inside after the hydro dipping is complete) DIY complete hydrographic printing kit. Object to be dipped. Sandpaper to smooth the surface. Rags. Bucket of mild cleaning solution and water. Vinyl, rubber, or latex gloves.
What is the activator for hydro dipping?
INK DRINK FILM ACTIVATOR. INK DRINK Hydrographic Film Activator is an easy to use film activator, compatible with most films on the market. Ink Drink maintains the richness and color vibrancy of your film and activates most films with a single pass (one coat).
What is Hydro film activator?
Activator is the key element in the hydro dipping process. It is a chemical so integral to the process of hydro dipping that it acts as a key difference between successful and unsuccessful dips. The activator is applied to the film to make it dissolve and turn the film ink into liquid.
What primer do you use for hydro dipping?
Any paint requires a good primer to stick to, and a clear coat to seal the paint in after and offer ultimate protection. Rust-Oleum Painter’s Touch Flat White Primer is the go-to for hydro dipping.
Do you let the primer dry before hydro dipping?
Apply a very light dust coat and leave to dry for 15 minutes. Sand, clean and paint your item in an appropriate primer, and base coat prior to . The base coat is a big part of some hydro dipping patterns as they have a lot of clear parts in and it affects the hue of the finish on solid colour patterns.
Can you Hydro dip without a base coat?
Choosing the right base coat color is very important in hydro dipping. So if you are wanting the design to look as intended and usually shown on the product page of where you are purchasing the film, then using a white base coat is usually the best choice unless it is specified that another color was used in the photo.
What clear coat do you use for hydro dipping?
TWN’s clear coats are specifically designed for hydrographics. No matter your project or application, we have a clear coat with the unique characteristics that you need to create a long-lasting finish. CCI clear coats are the ultimate clear coat for sporting goods items.
Can you Hydro dip a tumbler twice?
Sometimes you’re not happy with your initial hydro dip so you want to give it another coat to cover up the old paint. Or maybe you want to dip more than once to merge multiple graphics and create cool effects. If you’re going to do this make sure your product is dry before dipping again.
Can you dip a tumbler in epoxy?
Once the mug is fully dry, it’s time to seal it. I prefer to use epoxy resin for my top coats because they come out so shiny and smooth. I wanted some sparkle to the hydro dipped tumbler so I added 4 different colors of glitter to the epoxy mix.
Can you use acrylic paint to Hydro dip tumblers?
Can You Hydro Dip with Acrylic Paint? Yes! Acrylic paint is usually heavier and needs to be thinned by mixing with water before adding it into your dipping water. Depending on the paint you’re using, you may need to add some cornstarch or borax to add density to your water.
Can u Hydro dip glass?
These hydro dip glass bottles are colorful and unique and the paint technique is easy. You will never get the same paint finish twice with hydro dipping. I have photos, a tutorial, and a video showing the process. Definitely watch the video because the technique is so much easier to follow.
What spray paint do you need for hydro dipping?
You can hydro dip any item with a nonporous surface — all you need are a few simple supplies! Step 1 – Using your 2x Rust-Oleum Spray Paint prime the item that you are going to Hydro Dip. Allow that to dry.
Can I Hydrodip at home?
It’s the original (and patented) DIY hydro dipping kit. The process formally known as water transfer printing was once only available commercially. MyDipKit was designed for the everyday, do it yourself Hydro Dipping enthusiast. The kit contains the basic supplies needed for processing parts at home.
