Table of Contents
How do I hook up my water line to my refrigerator?
Instructions Turn Off the Water. Locate the fixture shutoff valve on the cold water supply line under the kitchen sink. Disconnect the Faucet Water Line. Connect the Tee Adapter. Connect the Faucet and Refrigerator Supply Tubes. Connect the Supply Tube to the Refrigerator. Turn on the Water.
How much does it cost to hook up a water line to a refrigerator?
A typical water line costs between $65 and $170 to run. The cost to install a basic refrigerator on a first floor kitchen with a water line is about $250. If you need an electrical outlet installed by an electrician, you’ll need to pay an average of $220-$750 per outlet.
Can I use plastic tubing for ice maker?
To hook up a refrigerator ice maker, you will need to connect a line of plastic or copper tubing to a cold water line to carry water to the refrigerator. Plastic tubing is less expensive and easier to install than copper.
Can a fridge make ice without a water line?
A water line allows you to make ice in your refrigerator. Refrigerators that feature built-in water dispensers or automatic ice makers need to be connected to a water source. Fridges without ice makers or water dispensers don’t need any type of water source to function properly.
Do you need a water hookup for a fridge?
Of course, if your refrigerator doesn’t have an ice maker or water dispenser, or if it has one or both features but you prefer not to use them, there is no need to install a refrigerator water line.
Does Home Depot install water line?
Our plumbing installation services are backed by a 1-year limited labor warranty from The Home Depot.
Why is my Frigidaire refrigerator not dispensing water?
Make sure the water filter is positioned properly – simply remove and re-install the water filter to double check. The water filter may be clogged or overdue for replacement. If water is dispensing slowly or not at all, or your water filter is older than 6 months – it’s time to replace.
What is the best material for a refrigerator water line?
The best material for your refrigerator water line is braided stainless steel, however, that can cost a lot of money. Between plastic and copper, it really depends on preference. Copper is strong but it corrodes and gets kinked. Plastic is a good choice, but it’s not nearly as strong as copper.
Why can’t you use vinyl tubing for ice makers?
Why can’t you use vinyl tubing for ice makers? Answer: You’re right to be concerned, because plastic tubing to an ice maker is susceptible to cracking and splitting. By the way, you may notice a piece of plastic tubing rising vertically from the water valve to the rear of the freezer compartment.
How far can you run a water line for a refrigerator?
Only supporting it, and there is no requirement as to how it must be supported. Every 6 feet on 1/2″ copper pipe is sufficient for support.
Do all fridges with ice makers need plumbing?
| Many refrigerators with built-in ice makers and faucets need to be connected to the kitchen water supply, while others do not have plumbing. However, these disconnected refrigerators use a water tank to make ice and water, which must be filled manually.
What can I use if I don’t have an ice maker?
If you need ice but can’t find your ice cube trays, just grab a zipper bag. Whether you use a gallon, quart or sandwich size, it’s easy to fill a bag with water, zip it closed and toss it in the freezer. Remember to leave some air space in the bag, since water expands as it freezes.
Does upright freezer need water line?
Is A Water Line Required For A Chest Freezer? You do not have to connect your chest freezer to a water line. You can install a water line if you use the ice maker or dispense water. But even so, a water line is not mandatory.
How do you tap into a PEX water line?
1 Answer. First you need to cut the PEX tubing at the access spot. That can be done with a PEX tubing cutter. Then you acquire the correct type fitting (your size requirement may differ from picture) to rejoin the cut PEX with “T” fitting and a branch connection for an added PEX tubing to go off toward the ice maker.
Can you use SharkBite on PEX?
SharkBite brass push-to-connect fittings are compatible with PEX, Copper, CPVC, PE-RT and HDPE pipe. SharkBite fittings come with a PEX stiffener pre-loaded into the fitting for PEX, PE-RT and HDPE. The PEX stiffener does not need to be removed for Copper or CPVC applications.
What causes water dispenser to stop working?
Often times, the water dispenser in your fridge may have stopped working due to a frozen water supply tube. This is a common problem in side-by-side refrigerators in which the tube that connects your water supply to the door where the water dispenser is frozen due to improper temperatures.
What is PEX water line?
PEX stands for cross-linked polyethylene. It is a type of plastic tubing made from high-density polyethylene. It is used for radiant floor heat tubing and for water supply. PEX has a lot of advantages over copper piping, such as: It is far less expensive as a raw material.
Do refrigerator water lines need to be copper?
While water supply lines to refrigerators can be made of different materials like copper, plastic types and braided stainless steel, the good news is with adapters, most ice-maker supply lines should be able to connect to most refrigerators.
Is ice maker line same as water line?
The ice maker supply line is a small plastic, copper, or stainless steel water line that feeds directly into the ice maker. If the filter is clogged the ice maker will make fewer and smaller ice cubes. To check if the filter or water line is clogged, place a cup underneath the water dispenser.
Is copper line safe for refrigerator?
Best Water Line for Fridges However, copper can dent if something knocks into it, and these kinks can lead to leaks. You would have to be mindful of the copper tubing when moving the refrigerator. Some users might feel that copper tubing adds a metallic taste, but this is less common.
