QA

Quick Answer: How To Hook Up Electric Choke On Edelbrock Carburetor

Where do you connect electric choke wire?

For electric choke hookup, attach the bayonet end of the long electrical lead supplied to the positive terminal on the choke cap. The other end must be connected to an ignition activated 12-volt source. The distributor side of the ignition coil is NOT a 12- volt source. It is a 7-9-volt source after cranking.

What is the wire on the bottom of a carburetor?

The part in the bottom of the carburetor bowl is a fuel shut off solenoid. You should take it out of the carburetor and clean the plunger on it. There have been some issues with the solenoid closing and shutting off the engine.

Should choke be open or closed when starting?

The choke is only used when starting a cold engine. When doing a cold start, the choke should be closed to limit the amount of air going in. Once the car has warmed up, if the choke does not open fully, the restriction in air may result in reduced power.

How do you activate an automatic choke?

Watch the butterfly valves inside the carburetor while turning the automatic choke element clockwise until the butterfly valves are standing straight up. Turn the choke element counterclockwise until the butterfly valves are fully closed. Tighten the three automatic choke element screws with the screwdriver.

What is the difference between manual choke and electric?

Manually – A manual choke is controlled by a lever on the side of the carb. A lever or knob inside the vehicle is then attached by a cable. Electric Choke – An electric choke uses electricity to warm the spring and gradually open the choke.

How do you test an electric choke?

Check from red plug to ground to be sure you have power first. Your photo shows the choke in it’s cold or closed position. When you work the throttle the fast idle cam (other side of the carb) should rotate into the fast idle position. Turn the ignition on and wait a minute..now work the throttle again.

How does electric choke work Edelbrock?

The manual choke has a dash-mounted knob that operates a cable to open and close the choke plate, while the electric version uses a electrically heated coil that expands as it heats to open the plate.

How does a manual choke work?

A manual choke is a mechanical device that links a retractable knob in the driver’s compartment, via a cable, to a metal plate inside the carburetor. The metal plate moves to increase or decrease the amount of intake air in order to provide the optimum fuel mixture for the engine.

How do you test an electric scooter choke?

How do we test it? Start and run the bike (fast tickover is fine) for at least 5 minutes. ( Switch off the engine and *quickly* remove the moped choke unit. Now leave the choke for at least 20 mins to cool down and measure the distance again- distance B in the photo below.

Does an electric choke need a ground wire?

There is only one wire that goes to the electric choke on a Q-Jet. It grounds itself through the carb body. For this reason, you want to be sure to remove the round choke cover gasket when you install an electric choke. Otherwise, the electric choke will be isolated from ground, and it will never open.

What are the 2 wires on a carburetor?

The two screws on the side of the carburetor are the idle speed and the low speed mixture screw. The image below shows this. If the idle speed is turned, it will change the speed the engine runs when you throttle the engine down.

What is the solenoid on the bottom of carburetor?

The solenoid receives a charge when you turn the ignition which activates the small electromagnet inside and completes the circuit, turning on the carburetor. This allows you to start the vehicle because the carburetor is ready to start mixing the fuel and air combination that makes the engine turn on.

What are wires on lawn mower carburetor?

Premium Member. Those wires are for the fuel shut-off solenoid.It shuts off fuel flow to the main jet,when the key is turned off. One wire will go to the wire that is hot,both on cranking,and running positions.

What happens if choke is left on?

Leaving the choke on for too long will cause unnecessary engine wear and waste fuel. The engine needs its fuel to be vaporised in order to burn it. This is done by the carburettor where the fuel is mixed with clean air coming from the air filter, and sent into the pistons to be ignited.

What does an electric choke do on a carburetor?

A choke valve is sometimes installed in the carburetor of internal combustion engines. Its purpose is to restrict the flow of air, thereby enriching the fuel-air mixture while starting the engine.

How long should electric choke stay on?

At 5°-10°C (41°-50°F), the choke plate should be fully open in about ten minutes.

What would be the effects of a sticking automatic choke?

If the choke valve sticks, the mixture will stay rich. Your warmed-up car will be hard to start, run poorly and waste precious gasoline. A bi-metallic spring in the choke housing on the carburetor is connected to the shaft that the flap rotates on.

How do you test a carburetor choke?

You should check the carburetor choke when the engine is cold. Lift the hood and remove the air cleaner to observe the choke. Have a friend sit in the car and tap the gas pedal lightly, just once. With this you should see the choke plate fully close.

Can you change electric choke to manual?

If your car has an automatic choke and is giving trouble, you can usually convert it to a manual one with a special conversion kit.