Table of Contents
To make sure boards are evenly spaced, place a nickel or quarter between the boards as a spacer. Some people like the look of visible nail heads on shiplap. To avoid visible nail holes, nail boards through the rabbet or tongue. Don’t feel that you have to apply shiplap to an entire wall.
Where do you put your nails on shiplap?
Place a nail through the top and bottom of each shiplap board where it crosses a stud. Use adhesive to glue the board down first or ask a partner to help you hold it in place.
Should you fill nail holes on shiplap?
Don’t forget to fill in any nail holes and gaps in the shiplap with spackle or caulk prior to painting. If you painted the shiplap prior to installation, fill in holes and gaps after the shiplap is in place and then touch up these areas with paint.
Can you brad nail shiplap?
Shiplap can be installed directly to sheet rock/drywall. Simply mark the stud locations for nailing the shiplap or you can apply a construction adhesive such as liquid nails. Use a nail gun with 18 gauge 1 3/4”long brad nails. Nail through the top flange which is the longer of the two flanges.
Do you face nail shiplap?
We always recommend face nailing shiplap and tongue and groove when installing it on your walls, ceiling, and as exterior siding. Face nailing means that you shoot your nail at a 90 degree angle to the board through the flat (or face) of the board.
How do you fill gaps in shiplap?
How To Caulk Seams On Shiplap Once you have installed your shiplap, run a bead of acrylic caulk (also known as latex caulk) along the seams where the shiplap ends butt up to a wall, inside corner or molding. Smooth out the caulk with a clean finger or rag so that the caulk fits neatly into the seam.
What to use to fill in nail holes?
Apply spackling paste to the holes with a putty knife. Slowly drag the putty knife over the surface of each nail hole to fill it. Spackling paste is the best material to use to fill nail holes in either plaster walls or drywall in a long-lasting way. It is also called joint compound or patching compound.
Do you put trim on a shiplap wall?
Shiplap walls laid horizontally work even when there isn’t crown molding to finish it. The top board is installed right up against our ceiling and caulked (it was installed the same way in my old kitchen). If you installed the boards vertically you’ll likely need a finishing trim of some sort at the ceiling.
Should I use brad nails or finish nails for shiplap?
We recommend using 16- or 18-gauge finish or brad nails. 1-½” to 2” in length should be sufficient. Both gauges are strong enough to hold the lumber securely, but small enough as to not leave a large hole on the face of the board.
What is the difference between a brad nail and a finish nail?
Brad nails are formed from a fine, 18-gauge wire, so they are smaller in diameter than finish nails and typically have less holding strength. They’re better suited for tasks like light decorative trim and molding, panel installation and crafts.
Do you start shiplap from top or bottom?
The first key to installing shiplap is to always, always, always start at the bottom of your wall! This little piece of advice is actually good for two very important reasons. First, by starting at the bottom, it allows gravity to be a helpful aid as you work your way up the walls.
Where do you nail tongue and groove shiplap?
Avoid visible nail holes Install planks with the tongue up. Nail at an angle directly through the tongue and into your studs. You don’t need to nail through the face of the planks anywhere but on the bottom row and near the ceiling.
What do you fill nail holes with on shiplap?
For primed shiplap, since you’ll be painting it, you can fill in nail holes with a wood filler. Once you sand down the nail holes you filled in, paint over for a seamless look.
Do you caulk around shiplap?
The edges of the shiplap wall need to be caulked (with paintable caulk) wherever there is molding and then they need to be “cut in” with the paint brush. For my wall, we caulked the gaps along the inside wall corners (where we installed quarter round molding), the floor molding, and the top crown molding.
Does shiplap need a gap?
Traditional shiplap planks butt right up next to each other without any gaps, but UFP-Edge Timeless nickel gap shiplap features built-in spacing between each board.
Can you fill nail holes with toothpaste?
Top DIY ways how to fill nail holes in the wall: Toothpaste works best for small holes in the wall, particularly because it tends to crack. To avoid cracking, crush up some aspirin into powder, and mix it with a bit of toothpaste to create a paste. Then, apply the toothpaste-aspirin mix to the wall and let dry.
Can you use caulk to fill nail holes?
You can use caulk to fill nail holes in painted trim, but caulk tends to be messier and shrinks more than wood filler, and it can’t be sanded smooth like filler can. If you use caulk, make sure it is labeled as “paintable,” and don’t leave a smear on the wood surface, which might show up after painting.
Do you Miter shiplap corners?
If you’re wrapping shiplap around an inside or outside corner, or down a ceiling-to-wall edge, we always miter all those corners at a 45* angle to ensure a seamless transition and so that it looks like the board is literally wrapping around the corners.
