Table of Contents
Follow these simple steps to install exterior shutters on vinyl siding and give your house a new lease of life. Step 1: Measure your windows. Step 2: Check for the right screw length. Step 3: Drill pilot holes in the shutters. Step 4: Drill holes in the siding. Step 5: Install spacers. Step 6: Attach the shutters.
How do you attach wood shutters to vinyl siding?
Here are the steps to attach wood shutters over vinyl siding: Gather your work tools and materials. Measure the window frames. Ensure the shutters are properly sized. Mark the pilot hole locations. Drill the pilot holes. Attach the shutters to the vinyl siding.
Can you put shutters on siding?
Using metal screws with painted heads is an alternate method to install exterior shutters on all types of siding, stucco and masonry. Use a drill with a multi-purpose 11/64-inch bit to pre-drill holes through the shutter for the screws at each reference mark. Reposition the shutter on the wall.
Can you screw into vinyl siding?
A stainless steel screw is the very best, but also the most expensive. Vinyl coated screws are great too. No matter which screw you buy, make sure it is a Phillips head screw because they are the easiest to use. Obviously, you want to be safe when climbing ladders to drill into the siding.
How do you reattach vinyl shutters to vinyl siding?
If the shutter was ripped from the house, the holes may be stripped. Screw a two-inch weatherproof deck screw into each hole to ensure there is still “bite” to the hole. If the screw slips right in, fill the hole with wood filler. Use a Philips head screwdriver to insert the filler into the hole.
Where do you drill holes in shutters?
To help ensure proper alignment mark and predrill holes using a ¼” drill bit into the shutter before attaching it to the wall. With the shutter in location against the wall, drill through the shutter into the wall 2½” deep. Make sure you drill holes deep enough so the shutter fastener doesn’t bottom out.
How should shutters be hung?
When open, shutters should be located tight to the window covering all or part of the window casing and projecting outward at the window edge. Architecturally, it is not necessary for a feature to actually be functional; however, it must always appear functional.
What screws to use on vinyl siding?
Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. Aluminum trim pieces require aluminum or stainless steel fasteners. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig.
How do you find studs in vinyl siding?
Start at the top of the wall where you know there is a stud. Tap the end of the tape measure (or hammer) lightly on your siding. Tap it at each end of the wall, and at every 16 in. or so, until you hear a hollow echo in one spot. That means you’re in between the studs.
Is it okay to drill into siding?
If you want to attach items to the exterior of a home covered with vinyl siding, you must drill through the siding first and then into the structure of your home to properly secure them. While special tools aren’t necessary to drill into your siding, you must exercise caution when doing so to prevent damage.
How do you use shutter clips?
Push a shutter clip partially onto the ribs at each corner of the shutter with. Hold the shutter against the mounting surface in the position where it will be attached. After the Shutter-Clips are in position and fastened to the. Read all of Step 4 and view Figure 4 before installing Shutter-Clips.
How long should shutter screws be?
They are standard 2 ½ inch steel screws with the heads painted to match your shutters.
Can you reuse shutter holes?
Press the back of the plastic nail through the front of the shutter, exposing the mounting hole. Homeowners cannot reuse shutter loks or the plastic nails and will need to purchase a new set of plastic mounting nails.
How do you fix loose exterior shutters?
You will need to unscrew the hinge from the shutter and identify which hole(s) have become enlarged. Either step up to a thicker screw or repair the holes by using 2 pack filler* available in tube form that can be squeezed into the hole. Once dry, the excess can be carefully removed and lightly trimmed.
Can you drill holes in vinyl windows?
Unlike other materials, you cannot easily drill into vinyl and attach brackets in order to install your favorite blinds.
How do you install exterior shutters on stucco?
How to Install Vinyl Shutters on Stucco Measure and drill 1/4-inch holes in your shutter for your shutter locks or screws. Hold the shutter up next to the window in the location you desire. Drill through the stucco using a 1/4-inch masonry carbide drill bit. Hold the shutter over your holes.
How do you hang something heavy on vinyl siding?
2. How to Hang Heavy Things on Vinyl Siding Using A Wire Hook Step 1: Identify the location where you want to hang the item. Step 2: Disconnect the seam between the slats. Step 3: Lift the upper slat. Step 4: Reassemble the siding. Step 1: Mark a hole. Step 2: Select the right drill bit. Step 3: Drill through the siding.
Is it OK to screw into wood siding?
Although ring-shank siding nails are suitable for wood siding installation, screws have better holding power over time. Stainless steel is strongly recommended for all woods and required for modified woods such as Accoya and Kebony.
What’s behind vinyl siding?
The wood that goes under residential siding – exterior sheathing – performs several functions. It adds insulation, waterproofing and structural support for the framing. It also provides a surface on which to nail the siding. The most common sheathing materials include oriented strand board and plywood.
Which way do shutters go?
The correct installation of a fixed louver shutter should have the shutter louvers facing down and towards the back when the shutter is open (when it is not covering the window).
