Table of Contents
Use a small-link chain to suspend the fixture from screw-in hooks or eyelets. Otherwise, hold the fixture against the ceiling in the designated mounting location. Drill your holes into the ceiling and the studs or, if using toggle bolts, just through the ceiling. Screw the fixture to the ceiling.
How many fluorescent lights can you put on one circuit?
It’s possible to supply 48 lights with 40 watt light bulbs and still have a 20% safety margin with a 20 Amp breaker. When you only want to put 4 lights on a breaker, it’s unnecessary to have a breaker that is high.
How many fluorescent lights should be in a garage?
If you want the garage to have even illumination, reduce that amount by half. Four, 3-lamp fixtures should achieve even lighting over nearly all of the garage. If you don’t need to have the whole garage lit up, one or two of these fixtures should suffice.
What are the accessories used for fluorescent lamp installation?
These are the tools for installing a fluorescent light fixture: Screwdriver. Wire stripper with cutting blade. Wirenuts or solderless connectors. Replacement fluorescent fixture.
How are fluorescent lights hung?
Most fluorescent lights simply snap into place with a gentle push on either end. According to Exceptional Electric, the diffuser screen may be held on with clips, slide on from the side or hang from a lip on either side of the hanging fluorescent light fixture. Some may also be attached with small screws.
How do you connect fluorescent lights together?
Run a length of two-conductor wire from the existing fluorescent fixture to the new fixture. Loosen the screw on the side of the cable clamps on both fixtures. Feed the ends of the wire through the cable clamps and tighten the screws until the wire is secure.
Can you replace a fluorescent light fixture with a regular light fixture?
Sometimes, you want a light fixture with a little more pizzazz, or one that produces light that’s a little warmer than the cold, bright light that’s so common with fluorescent fixtures. Swapping out a fluorescent fixture with a regular, incandescent model is easy to do.
How do you remove fluorescent light covers without clips?
If your kitchen is lit by a single fluorescent bulb instead of several, its cover may be held in place with a nut on the side. Use pliers or a wrench to twist this nut counterclockwise. When it comes off all the way, you can slide the bulb cover away from the nut.
Can fluorescent lights be wired in series?
Measure the distance between each fluorescent fixture. Cut a length of 14/2 nonmetallic cable (NM) that measures 12 inches longer than your measurement. Repeat this step for each fluorescent light you will wire in this series.
What is a non shunted socket?
Non-shunted sockets have separate contacts – or points of entry for the wires – creating two tracks for the electrical current to travel. Non-shunted sockets have contacts that are not joined or connected. Most voltage meters will either light up or ring or beep if the electrical contacts are connected, or shunted.
Can you put LED bulbs in a T8 fixture?
Type A LED tubes need an existing T8 electronic ballast to operate. All you need to do is remove the existing T8 fluorescent lamp and install a new T8 LED Type A lamp.
Can you put lights and outlets on the same circuit?
Yes, you can. The average home uses an indoor distribution board that houses the breakers of the majority of circuits in the home. A circuit controlled by a 15A circuit breaker (which a lot of contractors use for general lighting) can also accommodate outlets.
How many fluorescent lights can be on a 15 amp breaker?
50 watt light equals less than 1/2 amp current flow at 120 volts. You can put up to 30 lights (based on 50 watt light) on a 15 amp breaker. You can put up to 40 lights (based on 50 watt light) on a 20 amp breaker.
How many fixtures can you have on a 15 amp circuit?
For a 15-Amp circuit breaker, this will be a maximum of 12-Amps. Assuming a 60 watt light, you can put up to 24 lights on a 15 amp breaker. If you are using low-wattage LED bulbs, an LED bulb using 10 watts, you can install up to 150 bulbs on a single circuit.
Do fluorescent lights work in cold weather?
Temperature Range Many fluorescent lights can’t operate if the air temperature is below 50 degrees Fahrenheit, which is not always due to the lights themselves but instead often has to do with the type of ballast used in the light fixture. Magnetic ballasts don’t work in cold temperatures.
How many lumens do I need for a 20×20 garage?
80-100 foot candles Garage Size Square Footage Target Total Lumens 12’x24′ 288 sq. ft. 23,000-28,800 14’x28′ 392 sq. ft. 31,360-39,200 20’x20′ 400 sq. ft. 32.000-40,000 22’22’ 484 sq. ft. 38,720-48,400.
Where should I put lights in my garage?
Ambient lighting should cast light evenly across the garage floor. So position garage door openers with built-in lights at the center of the ceiling; if using multiple flush-mount fixtures, install them at an equal distance from each other on the ceiling.
What are the common problems of fluorescent lamp?
defective starters, defective bulbs or a defective ballast. IMPORTANT: Flickering fluorescent tubes can cause the ballast to overheat and fail prematurely! They can even cause a starter to burn out! Don’t wait too long to fix the problem or you may end up with a bigger repair!.
What are the six parts of a fluorescent lamp?
Compact fluorescent components consist of cover, coil glass tube, phosphor coating, mercury vapor, ballast, ballast cover, and base.
