Table of Contents
Inspect the bathtub for remaining mineral deposits and soap scum. If white, chalky staining remains, spray it with full-strength white vinegar. Let the deposits and scum absorb the vinegar for 15 minutes.
How do you get stains out of a plastic bathtub?
For cleaning your plastic bathtub, rubbing alcohol is the best you can use. To clean your tub, start by flushing it out with hot water. Let it sit for about 10 minutes. Then, rub or wipe the surface of the tub with some rubbing alcohol on a wet paper towel or cotton ball to remove stains or mildew.
How do I get my plastic tub white again?
Combine baking soda and water to create a paste similar in consistency to toothpaste. Rub the paste over the yellowed surround. Allow it to set for up to one hour. Wet a soft nylon brush with warm water.
How do you make an old plastic tub look new?
For weekly cleanings, pour 1 cup of water, 1 cup of vinegar and 1 tablespoon of dish soap into a spray bottle. Spray this right on the fiberglass surfaces and allow it to sit for at least 15 minutes. Scrub gently with a nonabrasive sponge and rinse with clean water.
How do I get my yellow tub white again?
Hydrogen Peroxide: fill a spray bottle with 3-percent hydrogen peroxide. Let the solution sit for 10-15 minutes and then wipe the tub down with a damp sponge. You can repeat these steps until the yellow staining disappears.
How do I know if my tub is fiberglass or acrylic?
Look around the tub’s edges and see if it appears thinner; this could be an indication that it is acrylic. Acrylic tubs usually come in more colors than fiberglass tubs, as fiberglass tubs are commonly white. Acrylic also feels warmer to the touch than fiberglass, and tubs made of acrylic have smoother finishes.
How do you remove yellow stains from plastic?
Make a solution of water and bleach, using one tablespoon of bleach per cup of water. Let the containers and other items soak in the solution for one or two hours. After the stains are gone, wash the containers thoroughly, rinse, and dry.
Can you make yellowed plastic white again?
Fill a sink with an 8:1 water to bleach mix. Put on some gloves. Submerge the plastic in the bleach. Soak until white again.
How do you whiten a yellowed fiberglass tub?
Hydrogen Peroxide If your shower room has a fiberglass tub that has yellowed, a DIY cleaning solution of hydrogen peroxide and water will work wonders for you. Start by pouring the peroxide into your tub. Next, scrub the walls of the tub until they are clean. Finally, wash the tub by pouring water over it.
How do I get my fiberglass tub white again?
Fiberglass bathtubs may start to turn a yellowish color as a result of soap scum or hard water. These stains can be very difficult to remove. However, a mixture of cream of tartar and hydrogen peroxide will easily remove any stain and restore the tub to its original white color.
How do you change the color of a plastic bathtub?
Take time applying your paint to the entirety of the tub or shower in one even layer. Allow adequate drying time according to your paint’s instructions, then apply a second layer if necessary. Finally, you can finish with a layer of acrylic top coat to seal in your paint and add extra shine.
Can you repaint a plastic bathtub?
Acrylic enamel is the best material for refinishing plastic tubs, according to Miracle Method Surface Refinishing. Paint and a roller can be used to achieve an even finish, although it can take longer.
Can you sand a plastic bathtub?
Prep to Refinish Plastic Tubs Use a sponge and a bath cleaning product to remove any traces of grease or grime. You’ll then want to use a fine sandpaper to sand down your bathtub. This will help even out any larger cracks or scuffs. You’ll then want to wipe down your tub to remove any traces of the sanded surface.
Is my shower plastic or fiberglass?
Looking closely at the edges of your tub, thin edges could mean fiberglass, while thicker edges could indicate acrylic. Another tip to rule out cast iron as a material, hold a magnet to the side and see if it sticks. If it does not stick, you most likely have either fiberglass or acrylic.
Can you use bleach on fiberglass shower?
Stay away from bleach But bleach can also ruin the resin in fiberglass, so you don’t want to be scrubbing it onto tubs or your shower walls. Ammonia is safe on fiberglass though, so it’s a viable option. It’s especially good at getting rid of watermarks.
Can you refinish an acrylic bathtub?
Although made up of different materials, acrylic tubs can be refinished just as easily as fiberglass tubs. Acrylic bathtub refinishing is a great option if your bathtub’s surface is dull, damaged, or if you just want to change the color.
Can you bleach white plastic?
To whiten plastic, wipe the surface of the plastic with a bleach solution. To make the solution, mix 1 tablespoon of bleach per 1 cup of water. Use an old toothbrush to scrub the bleach into the plastic until it’s clean. Rinse thoroughly with soap and water after you’re done bleaching.
What causes yellowing of white plastic?
White plastic turns yellow over time due to a chemical reaction that occurs when it is exposed to light, oils, etc. If your plastic turned yellow from bleach or food coloring, those are actually dye stains. For those, use our guide How to Clean Food Dyes from Plastics.
How does hydrogen peroxide whiten plastic?
Whitening process. The reverse process uses commonly available 6% or 12% hydrogen peroxide and UV light as catalyst (can be common UVA bulb or even simple sunlight) to activate the whitening reaction. Ultraviolet light bombarding hydrogen peroxide generate very active hydroxyl and restore the original color.
