QA

How To Gauge Tire Tread

Take a standard U.S. Penny and insert it into the tread, with Lincoln’s head facing down and out. If you can see all of Lincoln’s face, your tread depth is below 2/32 of an inch, and you need new tires. Check your tires in multiple locations to be safe.

What is a good tire tread depth?

New tires typically come with 10/32” or 11/32” tread depths, and some truck, SUV and winter tires may have deeper tread depths than other models. The U.S. Department of Transportation recommends replacing tires when they reach 2/32”, and many states legally require tires to be replaced at this depth.

Is the penny test for tires accurate?

For years, motorists have been told the “penny test” is an accurate indicator of whether or not you need new tires. The test is conducted by sticking a penny head down in a tire tread; if you see all of Lincoln’s head, then you should change the tires. The one with an eighth of an inch of tread stopped in 300 feet.

Should I replace tires at 4 32?

The Tire Rack’s advice is that if rain and wet roads are a concern, you should consider replacing your tires when they reach approximately 4/32″ of remaining tread depth. Since water can’t be compressed, you need enough tread depth to allow the rain to escape through the tire’s grooves.

How often should your tires be rotated?

This common maintenance task—which should typically be done every 5,000 to 8,000 miles—isn’t one you should ignore. It may seem minor, but remember: Tires are the only thing that comes between your 2-ton vehicle and the road.

Is 5mm tire tread good?

Insert the gauge into the tyre tread groove with the coloured scale touching the tyre. If the red is visible the tyre tread is below 1.6mm. This means the tyre is 100% worn and should be replaced urgently. If the green is visible, the tyre tread is above is 5mm and is safe to drive.

Are 5 32 tires safe?

If your gauge measurement reads: 6/32″ or higher: Your tire’s tread depth is sufficient. 5/32″: If snow-covered roads are a concern, you should consider replacing your tires. 4/32″: If you frequently drive on wet roads, consider replacing your tires.

What is 6 32 tire tread mean?

6/32” Your tire’s tread depth is sufficient for 3-seasons but nearing minimum for a winter tire. 5/32” If wet roads are a concern, consider replacing your tires. 4/32” – 3/32” Seriously consider replacing your tires as soon as possible.

How many miles are tires good for?

Your tires should last 50,000 to 60,000 miles on average. But that really depends on the manufacturer. Some manufacturers build their tires to last up to 80,000 miles, while some design their tires to last as little as 30,000 miles. You can see how many miles to expect out of a tire by checking its treadwear rating.

How do you tell if you need new tires with a quarter?

The Quarter Test Insert a quarter into the tire tread upside down, with Washington’s head going in first. If the top of George’s head is covered by the tread, your tires are OK – do this test at multiple points around each tire. If the top of his head is visible at any point around the tire, you need new tires.

Why do new car tires wear out so fast?

The tires that came with your last new car were not designed by Michelin, Goodyear, Bridgestone or any other tire manufacturer. They were designed by the manufacturer of your car. This is because virtually all auto manufacturers specify very soft rubber which means they wear out too fast.

What percentage tread is 8 32?

8/32″ of useable tread depth. A tire that starts with 10/32″ of original tread depth has 12.5% wear for every 1/32″ that is worn away, and a tire that starts with 12/32″ ” of original tread depth, has 10% wear for every 1/32″ that is worn away, etc.

How many 32nds is a new tire?

New tires have an average tread depth of 8 to 9 millimeters (10/32 to 11/32 inches). As you drive, the tread will wear down. A tire with a tread depth below 1.6 millimeters (2/32 inches) lacks grip. Braking distance and vehicle control are impaired.

What is the penny trick for tires?

The Penny Test Insert a penny with Lincoln’s head upside down into a tire tread groove. If Lincoln’s head is covered and no longer visible between the grooves, your tread depth is good. If you can see all of Lincoln’s face, it means that the tire tread is 2/32 inches deep or less and it’s time to replace them.

How do you check tire tread with toonie?

Put the outside edge of the toonie in your tire’s tread. If the tread reaches the bear’s paws, your tires are probably pretty new. If it reaches all the way across the silver, they’re about 50% worn. If your tire tread reaches only about half-way into the letters, it’s time to shop for new tires.

Is it OK to rotate tires every 10000 miles?

It is important to rotate the tires front-to-rear several times during the vehicle’s lifespan in order to equalize tread wear and maximize the lifespan of the tires. Most manufacturers typically recommend rotating your tires every 5,000-10,000 miles, or at the same time as your regularly scheduled oil changes.

What happens if I don’t rotate my tires?

Without regular rotations, tire treads can wear down unevenly to create a rough and potentially unstable driving surface. In the end, this type of tire tread wear may decrease your safety on the road – think heat buildup, hydroplaning, poor traction in snow and ice, and an increased risk of punctures and blowouts.

How many mm tread before changing tires?

Fast facts: When to replace tires You must replace tires when the tread depth falls below 1.6 mm, which is the legal limit. Continental recommends changing summer tires at 3 mm and winter tires at 4 mm tread depth; after this point safety and performance characteristics are not optimal.

Is 7mm tire tread good?

Depending on their type, new tires have a tread depth of between 7 mm and 9.5 mm. This ensures the best performance in changing conditions. While the minimum legal tread depth for all passenger car tires in Europe is 1.6 mm, it is safer to replace them at a depth of 2 mm at least.

What tire tread depth is too low?

When is Tread Depth Too Low? The minimum legal limit is 2/32 of an inch. This doesn’t mean that tires are perfectly safe if they have 3/32 left of tread. This is simply the limit at which you won’t pass your state safety inspection.