Table of Contents
When should I float my concrete slab?
Float the concrete when you’re done grooving and edging (Photo 6). Floating removes the marks left by edging and brings the surface one step closer to a final finish. You may have to bear down on the float if the concrete is starting to harden.
How do you level a sloping concrete floor?
How to level a concrete floor that slopes (Must read) Plan first! How to clean the flooring properly. Mark where the uneven areas are. Grind down the uneven high points. Prepare Concrete bonding agent. Apply a bonding agent to the concrete. Prepare the self-leveling compound. Apply the self-leveling compound.
How many yards of concrete do I need for a 24×24 slab?
For example, for a concrete slab that is 24′ X 24′ X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
What is the difference between a float and a trowel?
STEEL TROWELS. Purpose: Used after floating to produce a smooth, hard, dense slab surface. What’s available: Steel trowels look similar to hand floats, except the blades are thinner and the handles are open rather than closed. The key difference among tools is the type of steel used for the blade.
Can you smooth out concrete after it dries?
Sand the Surface and Wash the Concrete Finish by fine-tuning with light sandpaper, until the surface is perfectly smooth. We recommend using a hand planer to smooth and compact the surface. If the concrete dries a lot then we recommend that you add water to the surface, this will help you give it a good finish.
What may occur if a slab is floated too soon?
More often, premature finishing or improper first (bull floating) or second floating results in trapping rising bleed water and air below the top surface of the concrete (Image 2). When this occurs, the resulting weak or soft zone below the surface causes the top surface of the concrete to flake or scale off.
What is the cheapest way to level a concrete floor?
There are self-leveling coatings designed to fill gaps and cracks. You could also try using vinyl floor tiles to make the transition more gradual. Probably the easiest (and cheapest) thing to do would be to get a big diamond grinding wheel and bevel down the lip.
Can you pour self-leveling concrete over existing concrete?
You can level an existing concrete floor with a leveling layer of new concrete, but you must prepare the old concrete floor first. Neglecting to prepare the old surface will prevent the new concrete from adhering correctly, resulting in a weak bond between the two layers.
How thick can self-leveling concrete be?
QUIKRETE® Fast-Setting Self-Leveling Floor Resurfacer (No. 1249-51) can be installed from 1-1/2 inch (38 mm) thick to a feather edge, although a ¼ inch (6.3 mm) minimum thickness is required for heavy traffic areas.
What does a floating slab look like?
Floating slabs are concrete slabs that are laying over the ground, without any kind of anchoring, as if it simply sits on it and floats. Floating slab, as the name tells it resembles a plate that is simply laid over water, with no kind of connection between them.
Do you need rebar for 4 inch slab?
The thickness of rebar should be no more than 1/8 that of the slab, so a 4” slab shouldn’t have steel greater than #4 or 1/2″ bar. It’s best to check with a Structural Engineer if your slab will bridge or cantilever. What is this? For 4” concrete slabs used for driveways and patios, #3 rebar is common.
How thick do I need my concrete?
Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.
How many yards of concrete do I need for a 10×10 slab?
The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.
How much does it cost to pour a 24×24 slab of concrete?
A typical 24×24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
Why does magnesium float for concrete?
Magnesium smooths the surface of fresh concrete and opens the pores for proper evaporation, all without pulling the surface like a wood or resin tool. Extruded floats are made by pushing molten magnesium through a die (think Play-Doh), so the floats are the same profile from end to end.
