Table of Contents
Whirlpool Washer Lo FL Error Make sure the water supply is turned on and you have proper water pressure being supplied to the machine. Make sure the water supply hoses are not kinked or pinched and that screens in the supply line are clear of debris.
How do you fix Whirlpool Lo FL?
Error Code F8 E1, LF, or LO FL all indicate that no water is detected entering washer after 13 minutes.If pressing Power does not work: Unplug the washer or disconnect the power for one minute. Plug in the washer or reconnect the power. Re-select the cycle and press Start.
What does Fl mean on washing machine?
If Samsung Washer FL Error Code appears on the display panel, it’s likely a door lock malfunction. It indicates the door lock cannot be locked after several attempts.
How do you reset the sensor on a Whirlpool washing machine?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
What does Fl mean on a front load washer?
Samsung Front-Load Washer Fault Codes Fault Code Washer Problem LO or FL Door lock error ds Door is not locked dc Unbalanced load Sud (F70) Too many suds.
Why does my Whirlpool washer say FL Lo?
The Whirlpool washer Lo FL error code is displayed when water is not detected entering the washer or it’s not filling the washer fast enough. Make sure the water supply is turned on and you have proper water pressure being supplied to the machine.
How do you fix LO FL?
The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.If code is still displayed: Unplug the washer or disconnect the power for one minute. Plug in the washer or reconnect the power. Re-select the cycle and press Start.
What is FL error code?
The P2 or FL error code is an indication that the drain pan in the unit is full.
What does LoC mean on my Whirlpool washer?
If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock and need to de-activate it to allow the washer controls to function. Some models will look like the following: This error code does not mean “Door Locked”.
Why does my washer say low flow?
If you only notice low water pressure when using the hot water setting, then you probably have a clogged hot water line (or vise-versa for cold water). The easiest solution to this problem is to replace the clogged line with a new one. Water lines can be purchased either online or at most major home improvement stores.
Do Whirlpool washers have a reset button?
While most Whirlpool washers can be reset by disconnecting the power, some models may have different instructions. You may be able to find the specific reset instructions for your model either in the manual or by locating the washer’s tech sheet, which is usually located under the control panel.
How do you clear the error code on a Whirlpool top load washer?
System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).
How do I reset my Whirlpool Cabrio Top load washer?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
What does rL mean on a washing machine?
The “rL” error code means that a load has been detected in drum during Clean Washer with affresh® cycle. The Clean Washer cycle is meant to run empty, with no clothing inside the washer. Remove items from washer drum and restart Clean Washer with affresh® cycle.
How do I fix E1 error on my washing machine?
E1 – water inlet alarm Check that the water faucets are not closed. Check that the water pressure in the house is over 20 kPa. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.
How do I fix F8 error on washing machine?
If the washer has an F8 E1, LF, or LO FL error, the door will be locked, and the control will be unresponsive.Remove F8 E1 Error Code: Unplug the washer or disconnect the power for one minute. Plug in the washer or reconnect the power. Re-select the cycle and press Start.
Where is the water level switch on a Whirlpool washer?
Look for the water level switch on the right side of the cabinet toward the back of the washer. The round water level switch attaches to the side of the cabinet. A rubber tube connects the water level switch to the washtub.
What is water inlet valve?
The water inlet valve on your washing machine is the part that connects the two water hoses to the machine, and it controls the flow of both hot and cold water. A problem with the valve can cause the washer to not fill properly or not fill at all. You can also test the valve to determine whether it has failed.
What does lf mean on a Whirlpool Cabrio?
Long Fill Fault Code Washer Problem LF (F30) Long Fill Ld (F32) Long Drain uL (none) Unbalanced load oL (F70) Overloaded.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load Washer Error Code Error Sud or Sd There are too many suds in the washing machine. F5 E2 The door is not locking properly. F7 E1 Indicates a motor speed sensing error, F8 E1 or LO FL The washer is sensing a low flow of water.
