Table of Contents
Can you fix a bad thermocouple?
Thermocouples are designed to detect a pilot light’s loss of heat and close the gas valve to prevent a gas leak. Replacing a thermocouple is a relatively easy fix that can take less than two hours.
Can you clean a thermocouple?
Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up.
How do you know if you have a bad thermocouple?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.
How do I reset my thermocouple?
Press the reset button on top of the box to turn on the pilot light. Hold the reset button between 30 to 60 seconds to give the thermocouple time to heat up. Release the button to see if the pilot light goes out. The pilot light should stay on after the reset.
Can I replace a thermocouple myself?
1 cause of pilot lights that won’t stay lit is a worn-out thermocouple. It’s easy to replace and a new one costs $5 to $10. Then detach the thermocouple from the burner and take it with you to the home center or hardware store to ensure you buy the right replacement.
What causes a thermocouple to fail?
METAL FATIGUE Like everything, thermocouples can’t stay new forever. Changes in temperature can cause regular expansion and contraction in metal, which will cause thermocouples to weaken over time. After enough time, metal fatigue can cause a thermocouple to break.
Why won’t my pilot light stay lit in my gas fireplace?
If the pilot light on your gas fireplace won’t stay lit, a very likely culprit is a component called a thermocouple. A thermocouple is a safety device and is a component of the ignition system. Its purpose is to not allow the gas valve to open if the pilot light isn’t lit.
What do you do if your pilot light won’t light?
You need to turn the valve to the off position for at least three minutes. Once you have had the valve at off for a few minutes, switch it over to pilot setting. You will need a match that is lit. Hold it to the pilot opening and push the reset button on your pilot control.
Can a thermocouple be bad if the pilot stays lit?
NO. The purpose of the thermocouple is shut off all gas flow if the pilot light goes out. The thermocouple is a basic safety feature on anything that uses a pilot light. If the pilot light goes out, the thermocouple will turn off the gas and prevent it from accumulating which can be dangerous or deadly.
How much does it cost to fix a thermocouple?
It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on. It will shut the gas off if it’s not.
How do you clean a dirty thermocouple?
The best way to clean your thermocouple is to use either a piece of steel wool or the coarse side of a sponge to gently clean off any soot or other remnants. You can use a pencil eraser to clean between the threads of the screw that connects the thermocouple to the control valve of your system.
Why does my gas heater keep shutting off?
If your furnace keeps shutting off, it could be due to low airflow. There are several indirect issues that cause low airflow. Dirty Air Filters. If you don’t change your air filters often enough, the filters will become dirty and clogged, which means the heat exchanger retains heat and eventually causes it to overheat.
What is the most common problem with water heaters?
Water leaks are perhaps the most common type of water heater issue you’ll face. Any water heater will start to leak eventually, as by nature water will eventually corrode your tank and create microscopic cracks or fractures. However, this isn’t always a sign that your tank is what’s leaking.
Are thermocouples universal?
Honeywell, White Rodgers, and other manufacturers make universal replacement thermocouples, usually with a 30-millivolts (mV) rating for standing-pilot furnaces. Electronic flame sensors are much less universal, and you must find the exact part specified for your furnace model.
Does an electric water heater have a thermocouple?
Not all water heaters use a thermocouple. Some of the more recent models use a mercury sensor to shut off the gas valve. An electric water heaters don’t use gas at all, and therefore doesn’t need any kind of emergency gas shut off. Thermocouples can fail and require replacement.
How much does it cost to replace a thermocouple in a gas fireplace?
If you need your pilot light fixed, most professionals will complete the repair for about $150, on average. When replacing a thermocouple or thermopile with the help of a professional, you can expect to pay between $150 and $250.
Why does my thermocouple keep getting dirty?
Under constant exposure to a hot flame, a thermocouple wears down over time. Even a slight residue can make the thermocouple malfunction. The fix here is as easy as removing the thermocouple, cleaning it with a wire brush or something coarse (even an ordinary dollar bill works), and replacing.
Do thermocouples degrade over time?
Aging is a phenomenon that results in higher-than-accurate temperature readings, while drift results in lower-than-accurate readings. While all type K thermocouples experience aging and drift, best practices can minimize the risks and prolong thermocouple life.
