Table of Contents
What do you put around edge of decking?
Another way to edge your ground-level decking is by using gravel or similar stones. Like the bricks, it protects the deck from plants. It also helps the deck from water pooling by providing drainage. Similar to stone bricks, it can also add to your deck’s beauty.
How do you hide the end of a deck board?
Another way to hide the ends is to install a border/perimeter board around the outside edges of the deck (bottom). This method can really dress up your deck, especially if you choose an accent color for this board. The downside of a perimeter board is that it requires extra framing underneath.
How do you finish decking edges?
Composite decking ends can be finished by picture framing, raised fascia board, painting the ends, attaching decking veneer, composite nosing strips, vinyl stair nosing cove, composite corner trim or plastic end caps. In short composite decking, ends must be hidden or blended into the look of the decking boards.
What do you do with cut ends of composite decking?
Sealing the ends with lumber wax will help prevent moisture absorption. Kim Katwijk The cut ends of composite decking will absorb moisture and can swell, as shown here. Sealing the end cuts with lumber wax will help prevent swelling.
Should deck boards overhang fascia?
When installing decking boards, be sure to allow for enough overhang to cover the fascia board and whatever additional amount you prefer. This means the installed deck boards should have at least 1.75 to 2.75” overhang before the fascia is installed.
What is a fascia board on a deck?
A DECK FASCIA BOARD is the board that runs around the perimeter of the deck for a seamless look. Fascia covers the wood perimeter joist of the deck frame and is sometimes called “rim joist cover.”.
How do you put a picture frame on a deck?
TRIPLE PICTURE FRAME BLOCKING METHOD Add Blocking to Corners. Place a solid block at all four corners of the deck, leaving 15″ clear space between the inside of the block and the inside of the corner. Add Corner Support Joist. Add Two Flat Blocks. Continue Blocking Edge. Add Second Support Joist. Block Substructure.
What do you use for fascia on a deck?
If you choose to add fascia, any kind of pressure-treated or otherwise rot-resistant lumber can be used. However, if you’ve opted for synthetic decking in one of the many colors available, you’ll want to consider using a complementary PVC fascia. PVC fascia typically comes in 1/2-in. x 11-3/4-in.
How do you hide the edges of a composite deck?
The question is, how do you hide the ends of composite decking? There are several ways to go about it. Some of your options include picture framing, installing fascia boards, coating the ends with paint, using end caps and plugs, or edging your ground-level deck with stone.
Why does composite decking have grooves?
Grooved-Edge Decking Appearance: The primary reason people choose grooved decking is because they don’t want to see deck screws messing up their deck’s surface. Grooved decking has slots cut into both sides so it can be installed with hidden fasteners.
How do you fill gaps in composite decking?
Fill small holes, using a putty knife, with a mixture of fine composite board shavings and silicone caulk. The consistency of the mixture should be thick enough that it will not seep out of the bottom of the hole. Match the color of the caulk to the deck boards.
How much overhang should deck fascia have?
Between one and two inches of deck board overhang is ideal when you attach an outer fascia board, or at least 1 ¾” to 2 ¾” of overhang before installing the fascia.
How much overhang should you leave on deck boards?
The edge of decking should never overhang more than one-third of the decking material. For your standard 5.5” decking, that is 1 ¾” overhang.
How far can deck boards overhang joists?
The American Wood Council states that cantilevers are limited to 1/4 the span of the joists. Joist Spacing (o.c.) Maximum allowable overhang cannot exceed 1/4 of the actual main span.
Does a deck need fascia?
If building a traditional treated lumber deck, fascia is not required since the rim joist can be stained matching the deck surface. When it comes to selecting fascia, keep in mind these simple options to dress up one of the most noticeable parts of your deck.
What are the parts of a deck?
Components of the Deck Footing. – Most decks begin by pouring concrete footings and attaching post anchors. Post. – Posts are attached to the footings and hold the support beams up off the ground. Beams. Joist. Ledgers and header joists. Deck boards. Drainage system. Hidden fasteners.
What is the span of a 2×6 deck joist?
2-grade 2×6 joists can span up to 10 feet 9 inches from beam to beam when spaced the standard 16 inches apart with a maximum live load of 30 inches per square foot.
Should deck joists be 2×6 or 2×8?
In general terms, joists spaced 16 inches on center can span 1.5 times in feet their depth in inches. A 2×8 up to 12 feet; 2×10 to 15 feet and 2×12 to 18 feet. The larger the deck, the larger the joists. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards.
What kind of wood should I use for a deck frame?
Pressure-treated lumber is ideal for deck framing. We also recommend using joist tape or a wood protectant to help shield cut ends from moisture damage.
Can you shorten a deck?
One of the most popular home improvement projects is renovating or replacing an existing deck. Depending on the original deck design, your first step is usually going to be the demolition process. Either a worm drive or circular saw would be the most commonly used tool for cutting apart old decks.
What is picture framing a deck?
“Picture-framing” refers to putting a border around the edge of a deck or porch. On a composite deck or porch, picture frames are constructed using square-edge boards and mitered corners to ensure a clean, finished look.
