Table of Contents
How do you hide the ends of Trex decking?
Install Fascia Boards Installing fascia boards is a common practice to hide the ends of composite decking boards. Like picture framing, it gives the decking a stylish and sleek look while hiding the exposed ends. The difference is, you will install it on the sides, directly over the edges and the rim joists.
How do you finish composite decking edges?
Conclusion. How to finish the edge of a composite decking is simple if you use picture framing to cover the board edges. You can also paint the edges, glue a veneer cap to the ends, attach a raised fascia board or add a composite corner trim to create a consistent look.
Do you need to seal cut ends of composite decking?
Kim Katwijk The cut ends of composite decking will absorb moisture and can swell, as shown here. Sealing the end cuts with lumber wax will help prevent swelling. Because the uncapped ends of the boards are free to pick up water, the core can absorb moisture, which can lead to all sorts of problems.
How much overhang should a Trex deck have?
Trex is a popular composite material with a maximum overhang of 102mm or around 4 inches. Between one and two inches of deck board overhang is ideal when you attach an outer fascia board, or at least 1 ¾” to 2 ¾” of overhang before installing the fascia.
Can you sand the edge of composite decking?
No, sanding composite decking could cause damage and void the warranty. MoistureShield’s built-in protection stands up against weather and wear. Our Elevate and Vision series feature a protective polymer cap to resist fading and staining.
What is Trex Trim?
Along with new profiles, Trex has improved the surface aesthetics of its moulding offerings with a matte finish that is aligned with contemporary home design trends and was developed as a direct result of homeowner demand.
How do you close off the bottom of a deck?
Using an Open Style. Wire mesh is an inexpensive material to use to seal off below a deck. It will prevent animal access to the area below your deck, but it will not form a visual barrier to the area. One option is to seal off the area with wire mesh, then use landscape plants to hide the wire.
What do you put around the bottom of a deck?
7 Creative and Functional Deck Skirting Ideas Wood Lattice. When you imagine a deck skirt, a wooden lattice is probably the first thing that comes to your mind. Solid Wood. Solid wood boards are another popular deck skirting option that’s easy to customize. Composite. Faux Stone. Brick. Shrubs and Plants. Metal.
Do you need to seal the ends of Trex?
Low-Maintenance With Trex Composite Decking You won’t ever need to seal or stain the deck, and you certainly don’t have to (and shouldn’t) paint it. And since Trex is a composite material, you don’t have to carry out long-term maintenance such as replacing rotted deck boards.
Is there a sealant for Trex decking?
Defy Composite Deck Sealer can be used on all composite wood brands such as: TREX, Fiberon, Azek, TimberTech, etc. It should not be used on solid plastic decking.
Can you paint the ends of Trex decking?
A: You are correct. Vintage Trex decking and other brands of composite decking made of a uniform mixture of wood fibers and plastic can be painted or even stained. Newer styles of composite decking capped with a shell of different material on the top and sides of boards cannot.
Can you overhang composite decking?
Like any other deckings, you can design composite decking to have an overhang. However, it should be a part of your deck planning and layout design. You can create overhang using several methods. For instance, after installing the decking boards, you may opt to leave a few inches off the boards.
Does a deck need an overhang?
When installing decking boards, be sure to allow for enough overhang to cover the fascia board and whatever additional amount you prefer. This means the installed deck boards should have at least 1.75 to 2.75” overhang before the fascia is installed.
How far can a deck board overhang a joist?
The American Wood Council states that cantilevers are limited to 1/4 the span of the joists. Joist Spacing (o.c.) Maximum allowable overhang cannot exceed 1/4 of the actual main span.
Do you need a special blade to cut Trex?
Diablo’s TrexBlade is the only recommended composite decking by Trex Company when cutting composite decking materials. These new blades deliver maximum performance and highest quality of finish; making it a ‘must-have’ tool for both professionals and DIYers planning composite decking projects.
Can you cut Trex decking with a circular saw?
How to Cut & Fasten Composite Decking. You can make simple cross cuts in composite decking the same way you would cut any soft pine—a power circular saw will work fine. A power miter saw can provide very accurate, straight cuts, and a table saw with support extensions can make all types of cutting easier.
Can you use Trex for landscape edging?
Trex is most widely known as a composite decking product and brand. For a period of time, however, many enterprising DIY’ers even started looking to and at Trex as a viable — effective, beautiful, and affordable — option for landscape edging.
Can you use decking as edging?
Decking lumber is used as ground level edging against a manicured lawn. Decks are an option for a garden design where otherwise there is no usable space. It can be tied to a building or a freestanding surfacing material.
