Table of Contents
What can I use instead of a bull float?
Fresnos are used for troweling slabs that do not require a hard trowel surface. A Fresnos will speed up the troweling process. Fresnos should not be used as bull floats. Troweling can also be accomplished by machine.
How do you sponge finish concrete?
Another great way to achieve a brushed finish is to use a sponge, says Chris Sullivan, national technical director for QC Construction. “As the concrete achieves a certain hardness, you start applying water to the surface with a hose, and use the sponge to work away some of the cream, to get the desired effect.”.
Can I make a bull float?
Professional bull floats can be made of aluminum or magnesium and are meant for long term and continuous use. Remove the cloth mop from the mop head, exposing the metal wire frame.
When should you Powerfloat?
A rough guide for considering when to begin power floating is when walking on the surface leaves indentations of 3-4 mm. If the concrete is too wet the machine will tear up the surface, and if it is too dry, it will not be possible to trim high spots or fill low spots effectively.
How long do you wait to bull float concrete?
Darbying or bull floating should be done immediately after “screeding”, or after the concrete has been tamped if tamping was done. This process should be finished before excess moisture or bleedwater appear on the surface.
How do you remove bleed water from concrete?
How to Reduce Bleed Maintain a strict water to cement ratio. Add sand. Add Supplementary Cementous Materials (SCM’s) into your mix. Add air entrainment to the mix.
What is salt finish concrete?
A salt finish is a simple and inexpensive way to dress up what would otherwise be plain concrete flatwork. It’s achieved by pressing coarse rock salt into the surface of fresh concrete, allowing the concrete to set, and then washing the salt away with a stream of water.
How do you finish a rough concrete floor?
To smooth a rough concrete slab, you will need to brush off all debris with a broom, then wash away the grime with a mop using neutral cleaner and warm water. Next, you will want to identify the areas with cracks or misshapen areas.
What is a sweat finish on concrete?
SSS happens from moisture that accumulates from the difference between the inside air temperature and the floor temperature. When the air vapor cools down and matches the floor temperature, condensation forms on the concrete, this is also known as concrete sweating. Moisture causes mold and fungus.
How soon after pouring concrete should you water it?
To put it simply, the goal is to keep the concrete saturated during the first 28 days. The first 7 days after installation you should spray the slab with water 5-10 times per day, or as often as possible. Once the concrete is poured the curing process begins immediately.
What’s the difference between a float and a trowel?
STEEL TROWELS. Purpose: Used after floating to produce a smooth, hard, dense slab surface. What’s available: Steel trowels look similar to hand floats, except the blades are thinner and the handles are open rather than closed. The key difference among tools is the type of steel used for the blade.
How do I get a smooth finish with quikrete?
Add concrete to any low areas and screed level. Once the concrete has lost its sheen, smooth the concrete surface using a wood float in an arching motion. NOTE: use a stiff-bristle broom to create a non-slip broom finish (all broom strokes should be made in the same direction).
Can you make a concrete float?
Most people think concrete can’t float because it’s too heavy. But if concrete is shaped in the right way and light enough, it can float just like any other material. Any object, including concrete, will float if it’s less dense than the water it’s placed in.
What is a Fresno trowel used for?
Purpose: Fresno trowels are designed to attach to long extension handles so finishers don’t have to walk out on the slab. They permit rapid work over large areas, such as driveways, but do not achieve the same degree of compaction possible with hand trowels.
Is it necessary to float concrete?
Floating has to be done on virtually every concrete job after concrete is poured and leveled. (Leveling is usually accomplished with a screed.) When done properly, floating pushes the aggregate down into the concrete and encourages moisture to rise, helping the concrete dry and creating a smoother surface.
Do you have to trowel concrete?
Trowel the surface Float the concrete when you’re done grooving and edging (Photo 6). You may have to bear down on the float if the concrete is starting to harden. You’ll be surprised that with enough scrubbing you’ll be able to bring a slurry to the surface of even a fairly hard slab.
What may occur if a slab is floated too soon?
More often, premature finishing or improper first (bull floating) or second floating results in trapping rising bleed water and air below the top surface of the concrete (Image 2). When this occurs, the resulting weak or soft zone below the surface causes the top surface of the concrete to flake or scale off.
How do you smooth out concrete after it dries?
These are the 4 steps in how to smooth concrete after it dries: Remove all imperfections on the surface. Vacuum up all debris and apply the adherent. Apply a new layer of concrete. Sand the surface and wash the concrete. Apply a layer of vitrifier to protect the concrete.
