Table of Contents
Measure from the bottom of the weight to the ground level mark on your string. This is the depth of your well.
How can I tell how deep my well is?
How to Measure Lower until you feel slack. Note, you may feel some bouncing as you pass the pump depending on the space from the casing to the weight on the measuring line. Mark the line at the top edge of the casing. Pull out and measure. This is your well depth – the distance to the bottom of the well shaft.
How do I know if my well is deep or shallow?
If it is small diameter, such as 1-1/4” PVC, that would indicate it is a shallow “well point” as they are called. If it is 2″ or above, it very well could be a deep well. Larger casings may also be shallow wells. Some of the largest diameter wells are very shallow (bored wells).
How deep are residential wells?
Most household water wells range from 100 to 800 feet deep, but a few are over 1,000 feet deep. Well yields can be increased by fracturing the bedrock immediately around the drill hole and intercepted rock faults.
How do I find the water table in my area?
How To Find The Water Table In My Area? Call your local County Extension Office. It may have statistics for the average annual water table level in your area. … Look online. Check out the website for your local Water Resources Office. … Dig. This is the most reliable way to find the water table level on your land.
Is 4 gallons per minute a good well?
A standard 6-inch diameter drilled well can store 1½ gallons of water per foot of well depth. Alternatively, the New Hampshire Water Well Association recommends a flow rate of 4 gpm for a period of four hours as an optimum water supply capacity for a private domestic supply.
How far from the bottom of a well should the pump be?
Pumps should never be set directly at the bottom of a well. It is usually best to place the pump 10 to 20 feet up from the bottom of the well.
Are shallow wells better than deep wells?
Deep wells have higher protections against potential surface contaminants. The equipment involved in these types of wells is less visible than with shallow wells, which require an above-ground well housing to contain the well pump. Their water tends to last longer and require less monitoring for quality.
How do I dig a well for my house?
10 Vastu Tips To Construct a Well in Your Home Location of the Well in Your House Premises. Avoid Red Line While Digging Well. Avoid the Strictly Prohibited Directions for Constructing Wells. Perform Puja Before Excavating a Well. Never Dig a Well When a Woman in a House is Pregnant.
How many years does a water well last?
The average lifespan for a well is 30–50 years. 2. How deep is the well? Drilled wells typically go down 100 feet or more.
Is it OK to drink well water?
Well water can be safe for drinking and all other household needs, as long as you make sure to test your water supply regularly and select treatment solutions in line with your results. Learn more about the well water treatment options that are available for your specific needs.
How deep should a well be for drinking water?
The quality of your water depends on several factors including geology and water levels. In order to allow for maximum ground filtration to remove impurities, your well depth should be at least 100 feet. As a general rule, the deeper you drill, it’s more likely that there will be minerals present.
How far below ground is the water table?
Groundwater may be near the Earth’s surface or as deep as 30,000 feet, according to the U.S. Geological Survey (USGS).
How fast do wells refill?
In ideal conditions, a water well will refill at five gallons per minute. It takes two hours to fill a 600-gallon well. Not all wells exist under ideal conditions. There are several factors that can speed up or delay the time it takes to refill.
What is considered a good producing water well?
A well yield of 5 gallons per minute of sustained flow (measured over 24 hours or over 5 hours in some standards) is considered by most authorities as adequate for a one family residence.
Do wells run out of water?
When a well “runs dry” it doesn’t mean that the well will never produce water again. Aquifers can recharge through a combination of more precipitation and less pumps pulling water out of that aquifer. Sometimes wells can run dry permanently, but that is quite uncommon.
What will happen to a well if the water table drops below the bottom of the well?
When water levels drop below the levels of the pump intakes, then wells will begin to pump air – they will “go dry.” Pumping a well lowers the water level around the well to form a cone of depression in the water table.
How many gallons per minute is considered a good well?
5 gpm (two fixtures running simultaneously at 2.5 gpm) is a good estimate of peak demand, for the typical household. Water wells that reliably yield 5 gpm should be able to meet peak and daily needs for most residences. Wells yielding less than 5 gpm, however, are sometimes the only water source available.
