Table of Contents
Take an extra length of wire and run it over a section of underground wire. Carefully dig out the underground wire at both ends of the run. Cut the underground wire at both ends and connect the above-ground wire to make a bypass. If the transmitter stops beeping you found the break.
How do you find a break in an underground dog fence?
Begin to follow the twisted wire with the radio towards the main dog fence loop. You will begin to hear a combination of two sounds as you follow the twisted wire. Should there be a break in the twisted wire, the sound will slowly switch from two sounds to one sound.
How do you find a partial break in an invisible fence?
Plug in the Fence Transmitter and check the Loop Indicator Light. If the Loop Indicator Light is on you can assume the break is in the other half of the Boundary Wire. If the Loop Indicator Light did not come on and you hear a continuous beep, you may assume there is a break in this portion of the Boundary Wire.
How do I find the break in my invisible fence with RF choke?
If you have a strong signal on both ends connect them with a piece of wire, disconnect the choke and reconnect the wires from the fence into the transmitter. If the alarm goes off, congratulations, you’ve found your break!.
Why is my invisible fence beeping?
Why is my Invisible Fence control panel beeping? If your Invisible Fence control panel is beeping every second, the most likely issue is that you have a wire break somewhere on your property. These can be caused by digging too deep when working in the yard, burrowing animals, and even the weather.
How deep is an invisible fence buried?
In most cases, the wires should be buried in a trench that is between 1 and 3 inches deep; burying the wires at this depth allows adequate transmission of the signal, while protecting the wire from damage from lawn mowers and other activity on the lawn.
How do you find a break in an underground dog fence with an AM radio?
Check the Break If you get a strong signal on both ends, connect them with a wire piece, then disconnect the RF choke. Reconnect the wires from the perimeter into the transmitter. Fingers crossed, if the alarm goes off, there is your break!Mar 24, 2021.
How do you test a dog’s extreme fence collar?
How are you testing the collar? To test it properly, you must approach the fence in one place, then go back into the center of the yard and walk back out to another spot. Walking parallel in the beep zone will not cause the collar to activate again. You have to walk in and then back out again to test.
What gauge wire does Invisible fence use?
20-gauge wire is what you will find in most pre-packaged do-it-yourself fencing kits. Most professionally installed systems use the more substantial 14 or 16 gauge wire.
What is an RF choke?
We can think of RF chokes as applications of inductors. They are designed as fixed inductors with the purpose of choking off or suppressing high-frequency alternating current (AC) signals, including signals from radio frequency (RF) devices, and allowing the passage of low-frequency and DC signals.
How do you break an electric fence?
They can break the fence by destroying stands or by cutting the wires. Criminals can also crawl under an electric fence by simply propping up the wires with sticks for those fences that extend to the ground.
How do you reset an invisible fence?
Resetting the system can be as simple as replacing the batteries in your transmitter. Bring your dog inside, and turn off the power to the fence. Unplug the transmitter. Look for metal objects around or on top of the fence.
Can a dog jump over an Invisible Fence?
Although the installation of Invisible dog fences is a little troublesome, it is very successful in keeping your dog within the restricted area. Your dog cannot tunnel under or jump over the invisible fence.
How do you test an Invisible Fence collar?
Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.
How long do invisible fences last?
How long does the Invisible Fence wire last? Invisible Fence boundary wire is a direct burial grade wire and has a life expectancy of 27 years left undisturbed in the ground.
Are Invisible Fences cruel?
Invisible fences deliver a painful shock when dogs cross a buried electrical wire. Beyond the physical pain and the anticipatory fear that the shocks induce, these devices can injure a dog both physically—from burns to cardiac fibrillation—and psychologically, causing severe anxiety and displaced aggression.
How do I know if my Invisible Fence is working?
A light on the battery tester and audible tone on the receiver confirms that the collar is operating properly. If you get the audible warning but not a light, replace the battery.
Can you use a bark collar and an Invisible Fence collar?
We do not recommend the use of any ultrasonic bark control product in conjunction with invisible fences (especially not shock fences). Doing so will confuse the dog and cause a lot of frustration for both you and your pup.
How do you adjust the intensity of an Invisible Fence collar?
How to Change the Strength of an Invisible Fence Push the button on the receiver. A light on the receiver will flash. Adjust the distance from the boundary wire to trigger a warning alarm. Most transmitter boxes have a knob or lever to use to change the distance. Change the metal prongs on the receiver.
Why is my extreme dog fence collar flashing?
PLEASE NOTE: The red flashing light on the receiver indicates a low battery in the collar that needs to be changed. Slowly approach your outside boundary loop wire and listen carefully for the warning beeps.
