Table of Contents
Choose a stair rise somewhere between 7 and 7-1/2 inches. Take your total height divided by that stair rise number. This will almost always give you a long decimal number. Round to the nearest whole number – this will be the number of steps you will have in your staircase.
How do you calculate rise and run for stairs?
The vertical distance between the floors to be linked by the staircase is the principal determinant of the riser and tread dimensions. You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14).
What is the formula for calculating stairs?
How to Calculate Stairs – Example 1 450mm / 150mm = 3. This tells us that with a riser of 150mm we will need 3 risers/steps. 450mm / 2 = 225mm. Twice the Rise plus the Going (2R + G) should be between 550mm and 700mm. 2 x 150mm + 275mm = 575mm.
How many stringers do I need for deck stairs?
Deck Stair Basics Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How long of a board do I need for stair stringer?
Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step.
How many steps What is the number in a staircase?
Understanding Vastu for The Number of Steps in a Staircase The number of steps in a staircase should always be odd (15, 17, 19, or 21). The number must never end with a 0.
Can I use 2×12 for stair treads?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. The stair treads should be at least 36 inches wide.
How far apart should risers be?
Stringers should be spaced no more than 36 inches apart from each other for maximum stair support, according to the International Association of Certified Home Inspectors.
How many stringers do I need for a 36 inch stairs?
If cut stringers are used in the stair construction, then at least three stringers are required. Cut stringers should be spaced no more than 18 inches on center. For example, a 36-inch-wide stairway should have three stringers. If the stairway is wider than 36 inches, four stringers should be installed.
Can I use 2×8 for stair stringers?
You should attach 2×6 or 2×8 support framing under the rim flush to the bottom of the stringer. The stairs will hang here. Install a piece of blocking below the rim joist to extend the attachment surface for your stairs stringers. Use a level to mark the top step.
How far can a 2×12 stair stringer span?
A 2×12 stringer has a maximum unsupported span of 6 feet. These stairs (7) are likely to deflect and cause the stringers to either pull loose from the framing or shear along the grain.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has . 60 RET level.
What is the 18 rule for a staircase?
Rule one says that rise plus run (r+R) should equal 18 inches. Why? That’s what most people find to be a comfortable stride on most stairs. You can cheat a bit up or down, but below 17” and more than 19” will result in steps that require strides either too big or too small for most people.
How many stairs do you need to go up 10 feet?
As per thumb rule and various building code or IRC, assume standard design, for 12 feet height of staircase, you will need approximately 21 stairs and for 10 feet height you need 19 stairs to go up.
How high is a 2 step stringer?
Step stringers are cut for 2 In. x 12 In. treads, and have a 7 In. rise.
How long of a 2×12 do I need for stairs?
We suggest 10.5″ for 2×12 or 2 – 2×6 Treads. Treads may be cut to suit other widths. Either B or C is required.
How do you calculate stairs and landings?
When measuring straight stairs, measure from the back of the top riser (where it meets the previous step), over the nose (edge of the step) and down to the back of the next tread (where it meets the next step), then measure the width and jot both measurements down on your plan.
How do you calculate stair landing?
The height of the landing is determined by where it is located along the stair run. In this design, since it is half way from the top level, it is 8 steps high (8 x height of each step (6 7/8) equals 55 inches). The horizontal positioning of the mid-level landing is determined by the number of treads on the stair run.
How do you calculate stairs and landing?
Measure from the top of the stairs to the bottom, as this is the way the pile direction will go. Measure the width and depth of the doorways of your landing and hallway and jot down this information on your plan. Make sure to measure any drop backs or alcoves on the landing and hallway.
How tall is a 5 step stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in. x 11 in. x 60 in.).
Does the landing count as a step?
Does the landing count as a step? Yes it does. It amazes me how many people like to argue this one. Remember that when counting stairs, you are counting how many times you have to lift your foot.
Why do we have 13 stairs?
Building construction code has very specific requirements regarding the height of steps. This is to minimize the number of trips and falls. And the vertical distance between floors is fairly standard, given usual ceiling heights and joists supporting the upper floor. The result usually falls between 13 and 15.
Why do stairs have odd numbers?
Most staircases are and odd number of steps to help keep people from stumbling. Most people are right handed, so they naturally step with the right foot first. So if the top of the stair was an even number they would be on their left foot. But their brain is used to telling the right foot to go first.
