Table of Contents
How do I do a European mount on a deer?
European Mounted Deer Step 1: Harvest Game Animal Legally. Remove Head. Step 2: Prepare Head for Boiling. Step 3: Cook Meat Off Skull. Step 4: Clean Skull. Step 5: Wash and Degrease the Skull. Step 6: Whiten the Skull. Step 7: Prep Your Mount Surface. Step 8: Drill Your Holes!.
How do you prepare a deer skull for a European mount?
How To Make A Euro Mount Step-By-Step Remove the skin of the deer head. Using your knife, remove the skin from the deer head and remove the lower jaw. Boil the skull. Remove tissue. Add Peroxide. Wrap antlers. Boil skull again for 30 minutes. Remove shrink wrap and touch up as needed.
How long to boil deer skull for European mount?
When you’ve got as much tissue out as possible, cover the skull — not the antlers — with water and a few tablespoons of Amway dishwashing powder or its equivalent. Boil or, better yet, simmer the skull for about 1-1/2 hours (less for a small deer, as too much boiling can loosen the fragile bone connections).
How much does a European deer mount cost?
However, the average cost for a skull mount is only $150 and includes a plaque or other mount. If wanting only the skull mount done by itself, it is closer to $75. For the serious hunter who consistently harvests a mature buck each year, it’s easy to see that it can become costly.
How long do I soak deer skull in peroxide?
Place in hydrogen peroxide Leave the skull in the hydrogen peroxide until it has reached the desired whiteness. For a deer skull, this usually takes 24 hours. Be careful not to leave the skull in the hydrogen peroxide for too long.
How do you get cigarette smoke out of deer mounts?
Mix three drops of dish soap in a bucket with warm water, agitating it to create a sudsy solution. Saturate a clean sponge in the soap solution then squeeze out the excess solution so it is damp but not soaking wet. Use a wiping motion following the lay of the hair to clean the mount.
Where should I cut for a European mount?
1 | Remove the Head Cut to the bone behind the ears with a sharp knife. Cut around the neck to just behind the jawbone. Finish the cut by circling to the origin of the cut behind the ears. Make certain the cut goes all the way to the neck bone.
What to use to whiten a European mount?
Cover and protect the antler bases or any other part of the antlers from the hydrogen peroxide, using Vaseline or plastic wrap and tape or tinfoil. If the antlers are exposed to hydrogen peroxide it will lighten/whiten the antlers. If this happens don’t worry, you can just paint the antler back to life.
How do you make a European mount plaque?
How to Build a European Mount Plaque Step 1: Trace a Pattern. First, get a board that is about three quarters of an inch thick, and is big enough to cut out three shapes. Step 2: Cut Out the Shapes. IMG 0257. Step 3: Router the Pieces. Step 4: Stain and Clearcoat. Step 5: Mark and Drill. Step 6: Putting the Pieces Together.
How do you protect antlers when boiling?
You’ll want just enough water to cover the skull, but not so much that your antlers are totally submerged. While you’re waiting for it to heat up, wrap each antler in aluminum foil and secure with duct tape. This will keep the boiling water and steam from discoloring your antlers.
Should I boil deer antlers?
You should boil the antlers outside, otherwise they will stink up your house. Before beginning, test to see if the cooking pot is large enough to fit the antlers inside. All of the antlers should be submerged during boiling.
How long does it take a taxidermist to do a European mount?
There’s no need to meticulously cape out an animal’s head, neck and shoulders and pack the entire thing out of the woods. You can make your own skull mount in a couple days but it will likely take weeks or months for a taxidermist to finish one.
How much is a mounted deer head worth?
The long story short is you should expect to pay a minimum of $500 for a quality deer mount, and don’t be surprised if that figure pushes to $600 or more. Having been on the receiving end of several really bad mounts over the years, I know full well that you get what you pay for when it comes to deer taxidermy mounts!Apr 1, 2021.
How long does it take to mount a deer?
Eight to 12 months start to finish for a super-looking mount is reasonable. If you can get your deer back in six months or sooner, great, so long as the quality doesn’t suffer.
What peroxide to use for European mount?
Regular 3% hydrogen peroxide from your local Walmart will get the job done just fine. Fill your pot 50 percent full with hydrogen peroxide, then place the skull inside, and next fill the rest of the pot with water until it completely covers the skull.
Will 3% hydrogen peroxide bleach a skull?
Some bleaching is probably best, but not enough to make them completely white. Air-dried skulls may be bleached by soaking them in an approximately 3% to 6% solution of hydrogen peroxide. Hydrogen peroxide solutions that are used to bleach hair can be purchased from beauty supply stores.
