Table of Contents
To engage the blades, be sure that your throttle or choke is in the rabbit position. Then, push the PTO or blade engage lever forward into the on position.
Why won’t my Cub Cadet blades engage?
Common solutions for: Cub Cadet Lawn mower blades won’t engage. If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
Where is the PTO switch on Cub Cadet?
Find the small bell housing on the underside of the Cub Cadet’s Briggs & Stratton engine. This housing is for the PTO clutch.
Why won’t my lawnmower blades engage?
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
How does a PTO engage?
The PTO is engaged and disengaged using the main transmission clutch and a remote control mechanism which operates on the PTO itself. Typically, an air valve is used to engage the PTO, but a mechanical linkage, electric or hydraulic mechanism are also options.
How do I engage my riding lawn mower?
How to Engage Lawn Mower Blades on a John Deere Turn the key to the “on” position, advance the throttle to half speed and allow the engine to warm up for 2 minutes. Lower the mower to the desired cutting height. Engage the mower blades; push the lever to the right of the steering wheel all the way forward.
Why did my PTO stop working?
Basic Reasons The PTO Won’t Engage Your problem could be as simple as your transmission oil levels or air pressure levels being too low. If that’s the case, make the necessary adjustments and check to see if the PTO is engaging again. If your PTO is electric, first check for a bad electrical connection.
Why does my PTO keep turning off?
@mattk ,Matt, Something as simple as a low battery/bad connection or not charging could cause this. Possibly bad seat/reversing safety switch, faulty/loose wire/plug to clutch/PTO/switch, clutch faulty. Trouble shooting/parts/manual links below may help.
How do you engage a mower deck on a Cub Cadet?
To engage the blades, be sure that your throttle or choke is in the rabbit position. Then, push the PTO or blade engage lever forward into the on position.
Why wont my Cub Cadet go forward or reverse?
To operate your axles, your mower connects belts from the hydraulic pumps to the engine and from the engine to the mower deck. These conditions can cause the belt to slip off the pulleys, which can stop your mower from going forward or reverse.
How do I know if my PTO clutch is bad?
Activate the PTO engagement lever, then disengage it. Turn it on and off several times. If you do not hear a disengagement noise or see the power takeoff pulley stopping or slowing down at any time, it indicates the clutch and plates have galled together from excessive heat, or the slip ring has jammed.
Why does my lawn mower stall when I engage the blades?
The most common causes for a mower to stop when blades are engaged include the mower being in reverse, faulty safety switches, bad fuel, or clogged fuel lines. Trying to engage the blades in tall or wet grass can also cause the mower to die. While fuel can be a common issue, it might not be your issue.
Where is the PTO clutch?
The PTO clutch is mounted under the tractor or mower beside the power drive shaft, which is also vertically aligned. It is connected to the blade shaft, and when it spins, the blade spins too. There is a belt that is attached to the drive shaft and PTO clutch pulley.
How do you engage live PTO?
For transmission and live PTO Start by pressing the clutch pedal down totally and let it stay in place. Thereafter, you should shift the PTO switch to “ON” position. The PTO switch is usually positioned on the dashboard. Keep holding the clutch pedal down for about 5 seconds to allow the PTO to engage properly.
How do you start a choke on a riding lawn mower?
How to Start a Riding Lawn Mower? Sit firmly on the seat. Start the Engine. Press the Brakes. Engage the Parking Brake. Put the Gear to Neutral. Pull the Throttle onto Choke Position. Insert the Ignition Key. Turn the Key to the Right hand side/Clockwise.
Why is my riding mower not cutting?
Replace the riding mower blade belt The blade belt spins the blades to cut the grass. A worn or broken drive belt won’t spin the cutting blades so your mower won’t cut the grass. A worn blade belt can also cause mower deck vibration or uneven cuts. Examine the blade belt regularly and replace it if it’s worn or broken.
Why does my Cub Cadet keep shutting off?
The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the lawn mower for a long period of time. This sticky fuel can clog up the carburetor and cause the engine to stall. If the carburetor is clogged, try cleaning it with carburetor cleaner.
Where is the PTO switch on a John Deere mower?
Most John Deere lawn mowers are equipped with an electric PTO (Power Take Off). The PTO is the mechanism that turns on the blades located under the mower deck. The PTO works off of a 12-volt system. The electric clutch is operated by a switch located on the dashboard of the lawn mower.
What is a PTO clutch?
Power take-off (PTO) clutches provide a mechanical disconnect between the power created by gas and diesel engines or electric motors to another piece of equipment. The PTO clutches enable the transmission of that energy to auxiliary equipment that does not generate its own power.
