Table of Contents
How to Engage Lawn Mower Blades on a John Deere Turn the key to the “on” position, advance the throttle to half speed and allow the engine to warm up for 2 minutes. Lower the mower to the desired cutting height. Engage the mower blades; push the lever to the right of the steering wheel all the way forward.
Why wont my blades engage on my John Deere mower?
It could be your bearings and your spindle pockets, or spindles, have seized up,” says Oshel. If the blades are stuck, pump some grease into the fitting and carefully work the blades back and forth by hand until they move freely.
Why won’t my riding lawn mower blades engage?
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
How do I engage my PTO John Deere?
Front and Rear PTO Push down and forward on PTO switch (A or B) to engage PTO clutch. Pull back PTO switch (A or B) to disengage clutch.
Why is the blade on my lawn mower not spinning?
If your mower blades will not turn after the blade controls have been engaged, your deck belt may be broken. The deck is located directly under the operators seat. This belt spins the mowers blades and runs through a pulley system of idlers. If the belt has snapped, it will need to be replaced.
How do mower blades engage?
When the clutch solenoid is energized, the clutch engages the drive belt to drive the rotation of the lawn mower blades. If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage.
How do you engage the blades on a riding lawn mower?
Find the plunger at the top of the attachment lift lever. Press the plunger inward with your thumb, and move the attachment lift lever back, or toward you, to lower the cutting blade. Release the plunger and attachment lift lever. Pull the attachment clutch switch outward to “Engage” to make the cutting blade rotate.
Where is the PTO switch on a John Deere mower?
Most John Deere lawn mowers are equipped with an electric PTO (Power Take Off). The PTO is the mechanism that turns on the blades located under the mower deck. The PTO works off of a 12-volt system. The electric clutch is operated by a switch located on the dashboard of the lawn mower.
What would cause a PTO to not engage?
Two common reasons that a PTO won’t engage are installation issues and owner misuse. Addressing these possibilities first might be the only thing needed. Additional problems could arise if the switch is showing no continuity. Check for continuity using a multimeter.
How does the PTO work on a John Deere?
Driven by electricity provided by the mower’s 12-volt battery, the PTO clutch engages when its solenoid receives an electric spark. The PTO pulley is attached to the clutch and guides the belt that connects to the engine crankshaft pulley and rotates the blades of the mower that are located under the mower’s deck.
Should my lawn mower blade spin freely?
No, lawnmower blades normally should not spin freely as they are connected directly or indirectly via belts or other means to the engine. The blades should move freely in the housing and not touch the sides anywhere. Blades that produce a crackling sound when spinning sound alarming.
Why won’t my riding lawn mower move forward or reverse?
A blocked fuel filter can keep gasoline from flowing to your mower’s engine in adequate supply, resulting in a lawn mower that isn’t drivable. Damaged or clogged air filters also can prevent your lawn mower from going forward or in reverse simply because the engine will overheat quickly.
What is PTO clutch?
Power take-off (PTO) clutches provide a mechanical disconnect between the power created by gas and diesel engines or electric motors to another piece of equipment. The PTO clutches enable the transmission of that energy to auxiliary equipment that does not generate its own power.
Why does my John Deere riding mower dies when I engage the blades?
The pulleys in your lawn tractor are driven by the drive belt, and turn the spindles. If a pulley doesn’t spin freely, it can cause the engine to die when the blades are engaged. If a pulley doesn’t spin freely, it can cause the engine to die when the blades are engaged.
Which way does a tractor PTO turn?
“From the tractor seat?” “From the front of the tractor.” “It has to turn clockwise when you are facing it from the operator’s seat. Your pto actually turns counterclockwise.”Aug 11, 2015.
What is a PTO switch on a riding mower?
The PTO is a switch or lever found on tractors and mowers and stands for Power Take Off. This can be an electric switch or mechanical engagement that takes engine power to operate the mower deck or an implement. The PTO can run mowers by either a belt or a shaft.
What does live PTO on a tractor mean?
Live (two-stage clutch) A live PTO works with the use of a two-stage clutch. Pressing the clutch half-way will disengage the transmission while pressing it fully will disengage the transmission and the PTO. This allows the operator to slow down or change gears while the PTO is still operating.
