Table of Contents
What size hole do I drill for door latch?
The standard sized bore hole is 2 1/8″ in diameter. Through the edge of the door there is a 1″ cross bore that extends from the edge of the door through the bore hole. This cross bore is where the latch is installed. In addition to the two cross bores, a door can be prepped for one of 3 different types of latches.
How do you drill a bit for a door lock?
What are spade bits?
Also commonly known as paddle bits, spade bits have a wide, flat blade. The flat, broad blade of a spade bit has a pilot point attached to a 1/4-inch diameter shank that can be chucked into both regularly-chucked drills and quick-chuck impact drivers.
What is standard door latch size?
We generally recommend that a 76mm Overall Latch Size is ordinarily the best size for most lever handles. However the shorter 64mm Overall Size should be used where the door is glazed, to minimize the risk of hitting the glass rebate when drilling to fit the latch.
Will drilling through a lock open it?
Lock-drilling is a last-resort approach to gaining entry to locks that cannot be opened by other means. Drilling a lock will destroy the locking plug, but should leave the mechanism in working order.
What drill bits do locksmiths use?
The Locksmiths Hardplate TCT (Tungsten Carbide Tipped) Drill Bits offer an ideal solution to any drilling that is required. Available in a range of sizes, these drill bits are abrasion resistant and are ideal for drilling carbon or stainless steel.
What is the door latch hole called?
The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt. The diameter of the latch bore is generally 1” to accommodate bolts from either mechanical or electronic locksets.
How can I make my latch hole deeper?
Using the appropriate-sized spade bit and an electric drill, cut the hole in the door frame about 1/4 inch deeper. Test the latch mechanism again. If the twist knob stops in the same position with the door opened and closed, the hole is deep enough. If not, use the drill to make the hole another 1/4 inch deeper.
How do you fix a door handle if the hole is too big?
Cut a snug fitting circular plug thicker than the door, (even two tapered slightly to the inside), like big cork stoppers. glue with polyurethane wood glue, (dampen both door and plugs), tap in,wide side out, trim and sand. Then re drill new hole with holesaw of proper size.
How do you make a hole bigger without a drill?
To make a hole bigger without a drill, you need to get either sandpaper and a dowel, a hand file, or a jab saw. It’s helpful to draw the size of the circle needed first, then manually file the excess wood until the hole is the right size. Wipe away the dust and your project is ready to continue.
Why is an auger bit better if you have a deep hole to drill?
Drill Depth – Auger bits are capable of drilling deep, neat holes in wood up to 600mm (31″). Efficient Evacuation of Shavings – The wide, deep flighting of an auger bit allows for efficient evacuation of wood shavings and prevents the borehole from becoming clogged as easily as it might with other drill bits.
Can I use a spade bit instead of a drill bit?
To be effective, they should be used in a power drill or drill press. Spade bits bore rough holes, which are even more untidy if the bit is blunt. They are most effective on softwoods.
When would you use a spade drill bit?
Spade bits are for wood, plywood, and some plastics, and cut quickly with surprising precision. Use them only at high speeds, to prevent the bit from catching in the workpiece and the drill from trying to wrench itself from your grasp.
Are all door latches the same?
In the United States, there are two common backsets for residential door locks: 2 3/8 inches and 2 3/4 inches. Pack your locks with a 2-3/8-inch or 2-3/4-inch latch, depending on which backset you specify.
What is a tubular latch for a door?
A tubular latch is an item of ironmongery which is usually morticed* into a door, which allows the door to be opened and closed by means of a Door Handle or Door Knob. Firstly, the Tubular Latch is without doubt, the most common type of door latch on the market today.
Do bump keys work?
When executed correctly, lock bumping is effective in nearly 90 percent of all cylinder-type locks produced today. Perhaps one of the most disconcerting aspects of lock bumping is that it can often go undetected, which means that your home can be broken into without any signs of forced entry.
Where Can I drill a safe to open?
The most direct method is to drill into the face of the lock in order to reach the lever or drive cam. After accessing the lever or cam, the safecracker can use a punch rod to push them out of the way or bend them until they are no longer obstructing the path of the bolt.
What does TCT drill bit mean?
TCT (Tungsten Carbide Tipped) Drill Bit. Very abrasion resistant. Can withstand higher temperatures than standard high speed steel tools. Ideal for drilling carbon steel or stainless steel aswell as euro cylinders and other locks.
What are blacksmith drill bits?
Precision engineered HSS-G twist drills with reduced shank and split point. Suitable for drilling cast iron, non-ferrous metals, sheet metal and PVC.
What is cobalt drill bit?
What are cobalt drill bits? Cobalt bits are a combination of steel (or another alloy) mixed with a small percentage of cobalt, typically between 5 – 7%. Cobalt has a melting point of 1495°C and a boiling point of 2927°C, which makes it perfect for use at high temperatures.
Where do you drill a hole in a door knob?
Use a drill/driver with the 2 1/8” hole saw to bore a hole through the door. Once the center bit is through the door, stop. Bring the hole saw the other side of the door and finish the bore. Use the 1” hole saw to bore a hole through the edge of the door to create an area for the latch.
How does a door latch assembly work?
The latch assembly is the heart of the doorknob and is basically a spring-loaded bolt. This spring bolt—or latch bolt—utilizes a “spring clip” to force the bolt outward and into a hole in the doorframe. This holds the door closed. Once the bolt is fully retracted from the doorframe, the door can be pushed open.
What is a door strike plate?
Strike Plate This is the plate the latch-tongue, or deadbolt-tongue will connect with. It should sit flush with the door jamb. Any passage or privacy set needs to have a strike plate for the door to latch. Additionally, deadbolts need a strike plate to properly lock.
