Table of Contents
If you want to perform a drain-only cycle, turn on your LG washer and press the spin button and then press start. After a few minutes, the cycle will end and your washer should have drained out the water. Another way you can drain the water is by turning off your washing machine and unplugging it from the outlet.
How do I drain the water from my LG washing machine?
Press the POWER button to turn the washing machine off and remove the plug from the outlet. Locate the service panel on the bottom-left corner of the unit and open it. Unclip the drain hose and remove the plug from the drain hose to drain the water remaining inside the wash tub.
How do you drain water from a top loading washing machine?
How to Manually Drain a Top-Loading Washing Machine Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
Why won’t my LG top load washer drain?
Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.
How do I get the water out of my washing machine that won’t drain?
What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.
Where is the drain hose on washing machine?
The drain hose is usually found on the back of the washer, along with two separate hoses for both cold and hot water supply. The drain hose carries wastewater out of the machine, while the hot and cold water supply hoses bring clean water in.
Where is the drain pump on a washing machine?
The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.
Where is the drain hose on LG front load washer?
Locate the access panel in the lower front of your front-load washer. Next, grab a shallow pan and have it ready by placing it near the access panel to collect the water. Open and remove the acces panel by pulling the tab downward and out, revealing the drain hose and drain pump filter.
How do I drain the water from my Whirlpool top load washer?
Find the “Pause/Cancel” button on the control panel. Press this button twice to drain the washer. Press the “Power” button and rotate the cycle selection knob to “Drain and Spin” to remove the remaining water from the load. Check the washer’s discharge hose if the water fails to drain from the washtub.
How do I reset my LG top load washer?
How to reset the washing machine: Press POWER to turn the washer off. Unplug the washer from the power outlet or turn the circuit breaker to the unit off. With the power disabled, press and hold the START/PAUSE button for 5 seconds. Plug the washer back in, or turn the circuit breaker back on.
How do I manually drain my LG dishwasher?
Force the Drain. This is activated by pressing and holding 2 buttons simultaneously e.g DELICATE + DUAL CONTROL. The 2 buttons may vary depending on your model. If your model does not have a CANCEL & DRAIN option, start a cycle, let it run for 45 seconds, then power the unit off.
How do you install a drain hose on an LG washing machine?
Insert the end of the drain hose into the standpipe. Use a tie strap to secure the drain hose in place. If the drain is built into the wall, fasten the drain hose to one of the water inlet hoses with a tie strap. DO NOT install the end of the drain hose higher than 96 inches above the bottom of the washer.
Where is the drain pump on a top-load washer?
The drain pump is located underneath the washer and handles draining the tub between cycles. This guide will walk you step-by-step through replacing the drain pump for a top-load washer.
How do I test my LG washing machine drain pump?
Test the drain pump. Press POWER to turn the washer ON. Press the SPIN SPEED key until HIGH is selected. Press the START/PAUSE button to start the SPIN ONLY cycle. Listen to hear a humming sound which indicates that the drain pump motor has started working.
Do top-load washers have drain pump filters?
Top-load washers and standard top-load washers usually require removing the outer housing to access the water pump filter from the back of the machine. Cleaning this pump filter regularly will allow water to flow out more quickly taking suspended lint with it and not leaving it to redeposit on your clothes.
How do I manually drain my LG front load washer?
If you want to perform a drain-only cycle, turn on your LG washer and press the spin button and then press start. After a few minutes, the cycle will end and your washer should have drained out the water.
Do LG washers come with a drain hose?
A: Yes, the washer includes the drainage hose.
