Table of Contents
All Sundance hot tubs are equipped with a drain to remove the water. 680, 780 & Select Series hot tubs have a gravity drain. Simply remove the front panel and attach your garden hose to the drain and your hot tub will begin to empty.
Where is the drain on my Sundance spa?
Draining Your Sundance Hot Tub The drain is located at either the front of the side panel or behind the front panel. To operate, remove the drain cover, attach your garden hose and pull softly to open or simply attach your hose to the interior drain line to allow the water to flow out.
How do I get my hot tub to drain?
There are three methods for draining a hot tub: through the drain spigot (a.k.a. drain plug), using a submersible drain pump, or with the help of a wet/dry vacuum. Before you start draining the tub, however, cut off the power supply so the jets and pumps can’t accidentally be during this procedure.
How do you quick drain a hot tub?
How to Use It. All you need to do is put the devices wand into the water and shake it to prime. Then use the wand end to quickly vacuum sand from the bottom of your hot tub. Quick drain does not require electricity and no set up is required.
How do you get water out of the bottom of a hot tub?
Drop one end of a long vacuum hose into the spa, and connect the other end to the wet/dry vacuum. Turn it on for a few seconds – just long enough to let the hose prime and get the flow moving. Turn off the vacuum, and quickly disconnect the hose so the water can flow out onto the ground.
How do you drain a Sundance Spa 880?
Simply remove the front panel and attach your garden hose to the drain and your hot tub will begin to empty. 880 & 980 Series hot tubs come equipped with the built-in Quick Drain feature, which comes with a thicker hose for faster drainage. Just attach the hose and turn the gate valve to begin draining your water.
How do you start a Sundance spa?
Once the hot tub water level is above the top of the highest jet, switch the power on to the hot tub (switch the GFCI breaker on to power up your hot tub). Use the temperature up button to select your desired temperature, and the spa will begin to heat up.
How long does it take to drain a hot tub with a hose?
Drain your hot tub. Depending on the size of your spa, it should take around an hour to drain using the hot tub’s drainage spigot, or ten minutes to drain with a submersible pump.
Where can I drain my hot tub UK?
Draining your hot tub is very quick and easy, you will need to use a garden hose and attach it to the bottom of the tub where there is a drain spout. You will need to make sure that it is attached firmly and tight to the Spigot, the water will then start to drain out of your hot tub once you have opened the Spigot.
How do you use a quick drain?
Simply insert, shake, vacuum and drain. No need to towel out debris. Comes fully assembled. Works without pumps or motors.
Can I drain my hot tub into a storm drain?
Do not discharge chlorinated water from your pool or hot tub into a storm drain.
Do you need to turn off hot tub before draining?
Step #2: Turn Off The Power Not only is it dangerous to work with this amount of water while connected to a power source, it is also bad for your hot tub if the system powers on while its empty. Turn it off and completely disconnect anything electrical before you start to drain the tub.
What happens if you drain a hot tub without turning it off?
Alternately, don’t drain it and leave it empty for extended periods. Water left in the pipes and equipment can grow bacteria biofilm, which is difficult to eradicate. Plus, without water, seals and gaskets become dry and begin to leak. Therefore, make sure to not leave your hot tub sitting empty.
Can you drain a spa on the grass?
Where should you drain the water? This is not to be confused with a storm drain – never use a storm drain to drain your spa water. Otherwise, you can drain your spa onto your lawn and garden, given the chemicals have dissipated.
How do I reset my Sundance spa?
Solution: Try turning off the spa for 1-2 minutes, then reboot. This allows ample time for the board to get a full reboot. If problem persists move to next. Temperature overheat, a dirty filter or low flow conditions.
What does Flo mean on Sundance spa?
FLO. Stands for Flow Switch. Means that the flow switch is malfunctioning or the flow of water is being inhibited. The heater is deactivated and filter/circulation may be deactivated, also. Check for clogged filter and proper water levels in the hot tub.
What is the filtration cycle on a hot tub?
A filtration cycle is the amount of water that passes through your hot tub’s filter. Every hot tub is different, and you may have some control over this. However, this is the true test of the quality of your hot tub. The more water you can pump through the filtration system the cleaner it will be.
How long should a hot tub run each day?
Since your hot tub pump circulates the warm water as well as the sanitizer, a general rule is to follow manufacturer recommendations or leave the pump on for a minimum of eight hours per day.
Should I Shock hot tub after filling?
It is a good practice to shock with dichlor when you refill your spa. After that, regular maintenance can normally be accomplished with non-chlorine shock. Other times for shock treatment include before or after heavy use and when the spa has been neglected.
How often do you add chlorine to a hot tub?
A chlorine level of between 3-5mg/l must be maintained in your hot tub at all times. The addition of chlorine will depend upon usage and bathing habits. It could be daily or every 2-3 days (for 1mg/l add 2g per 1000 litres).
