Table of Contents
Here’s how to manually drain water from a Maytag washing machine: Pull the washer away from the wall and turn off its power and water connections. Scoop out any remaining water in the washer drum. Unhook the drain hose from the wall or sink drain and empty residual water into a bucket.
How do I get my washer to drain?
What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.
How do you manually drain a washing machine?
If not, follow these steps: Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
How do you drain a Maytag top load washer?
How to Drain a Top-Loading Washing Machine STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one. STEP 2: Locate the drain hose and water supply hoses. STEP 3: Drain the washing machine of water. STEP 4: Remove a drain hose clog. STEP 5: Remove a drain pump clog.
Why won’t my Maytag washer drain and spin?
A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.
Why is my Maytag washer not draining?
An obstructed drain hose is one of the most common reasons a Maytag washer won’t drain. Both kinks and blockages can obstruct the hose, preventing proper draining. However, if your washing machine is leaking, the kink may have damaged the hose, necessitating replacement.
Why won’t the water drain from my washing machine?
Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.
How do you position a washing machine drain hose?
In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.
Where is the drain pump on a washing machine?
The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.
How do you drain a washing machine mid cycle?
Press the “Start/Pause” button on the front of your washing machine and wait a few minutes for the washer to safely drain away water in the drum before it unlocks the door. Once this is done, you’ll be able to open the door and add/remove items or make chances to the cycle.
What is drain and spin on Maytag washer?
Use the recommended cycle/speed spin for your garment. To remove extra water in the load, select Drain & Spin. The load may need to be rearranged to allow even distribution of the load in the basket. If Low Spin or No Spin was selected, the washer might not remove enough water from the load.
Is there a reset button on Maytag washing machines?
Hold down the Delicates and Knits button for five seconds. The washer’s LED display should now flash and start to blink, which means the error codes have been resolved and the washer has reset.
Why does water stay in washing machine drum?
The outer drum is stationary and contains the water, the inner drum rotates and holds the clothes for washing and spinning. The water doesn’t drain out the bottom because the regular drain pipe is above the top of the drum – the water will stay until the drain pump is turned on during the drain and spin cycles.
Where is the coin trap on a Maytag top load washer?
Inside the center agitator: If you have a top-loading washer, inspect the center agitator. The cover may be removable, revealing a lint trap inside. At the end of the drainage hose: A small mesh screen may be fitted onto the end of the hose that drains water out of the machine.
How do you drain a Maytag washer for moving?
Transporting your washer: Disconnect drain from the drain system and drain any remaining water into a pan or bucket. Unplug the power cord. Place inlet hoses inside washer basket. Drape power cord and drain hose over the console and secure with masking tape.
Does a washing machine drain hose need to be elevated?
Yes, the drain hose should be raised, and it’s always safer to do so higher than the washing machine itself. This would eliminate the possibility of siphoning. You may also take other measures to ensure that you have the best drainage possible.
How do you drain water from washing machine before moving?
Be sure that both the hot and cold water valves are completely shut. Set the washer to warm wash and turn it on for 30 seconds to allow the water in the hoses to drain into the washer tub. Move the setting to spin to allow the water to drain out of the machine.
