Table of Contents
What is the standard rise for deck stairs?
An ideal riser height is 7 or 8 inches. The optimal tread width (from front to back) is 10 inches. Treads should never be less than 9 inches, nor more than 11 inches. Begin by measuring the total rise of the stairs, that is the distance from the ground to the top of the deck.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
Do deck stairs need footings?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How many stringers do I need for deck stairs?
Deck Stair Basics Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What is the code for outdoor steps?
Exterior Stair Construction The rise of the stairs should be between 125 mm (5”) and 200 mm (8”). This is measured from top of a tread nosing to the top of the next tread nosing or landing. The run should be between 210 mm (8 ¼”) and 355mm (14”). Unit run is measured from face of nosing to face of nosing.
What is code for stair height?
(1) The rise of every step in a stairway shall be not less than 4 inches nor greater than 7 1/2 inches. (2) The run shall not be less than 10 inches as measured horizontally between the vertical planes of the furthermost projection of adjacent treads.
How do I secure the bottom of my deck stairs?
How to Anchor Deck Stairs to Concrete Use your jigsaw. Notch out the bottom front of the center stair stringers to accept a 2×4 base plate. Make sure your stringers are level. Fasten the base plate to the stair stringers with screws. Locked in place.
Can I use deck pier blocks instead of footings?
Pier blocks can be used instead of footings for a ground-level deck not requiring permits. Piers blocks can also be used if the frost level depth is less then the height of the pier block.
Do deck stairs have to land on concrete?
Stair landings must be at least as wide as the stair and at least 3 feet deep. On the other hand, solid, flat, and stable materials, such as concrete, flagstone, pavers, or brick, can be installed with a measurable slope and will not usually shift under the weight of an off-balance person completing a stairway descent.
Can I make stringers out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
What size lumber are stair stringers cut from?
Selecting stringer stock Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible.
Can deck stairs land on grass?
Yes, it is a good idea to have a landing at the bottom of steps.
Can deck stairs land on pavers?
If you don’t want to go through all of the work involved in pouring a concrete landing for your deck steps, then you might consider flagstone, pavers, or brick instead. These materials are cost-effective and they will not require as much digging as would be necessary with a concrete landing pad.
What is code for steps on decks?
Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back. Stair treads must sustain a weight of at least 300 pounds in an area no more than four inches square.
Can I use joist hangers for stair stringers?
This will reinforce the stair stringer to rim joist connection and distribute the stair weight more evenly onto the deck framing. Cut them to fit the space perpendicularly between the rim joist and the next interior joist. Use joist hangers to fasten the blocking.
How do you attach wood stair stringers to a deck?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
How far apart can stringers be?
Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers. The maximum 18-inch spacing presumes treads of 5/4-inch wood decking or 2-by stock.
