Table of Contents
How do you make a rope lamp?
Step 1 – Start with a gross lamp. This is a $10 lamp I scored at a local thrift store. Step 2 – Gather your jute rope and tacky glue. So here’s the glue I used (it’s basic tacky glue. Step 3 – Wrap Rope around Lamp and secure it with glue. You can start at the very base of the lamp and work your way up.
Why do you never saddle a dead horse?
An important phrase to remember when applying a wire rope clip is “Never Saddle a Dead Horse”. This means you should never apply the saddle side of the clip over the dead end of the rope – the live end should always rest in the saddle.
How do you attach a man wire to a pole?
Ideally, the guy wires should extend out from the mast at a 45° angle, and should be anchored in screw eyes placed 120° apart (Figure 2). If four guy wires are used, they should be anchored in screw eyes 90° apart. Be sure each screw eye is firmly anchored in solid wood at least five feet from the base of the mast.
How do you make string Globes?
Instructions Cut String. Gather string and cut into 24″-36 lengths. Blow up balloons. Blow up balloons and have them ready at your work area. Mix your paste. Combine 1 cup flour with 1 cup water in a bowl. Coat a balloon. Coat the string & wrap balloon. Repeat. Let Dry. Popping time!.
What material can be used for lampshades?
Lampshades are made of fabric, parchment, glass, Tiffany glass, paper or plastic. Common fabric materials include silk, linen and cotton. Fabric shades are reinforced by metal frames to give the lampshades their shape, while paper or plastic shades can hold their shape without support.
What yarn is used for macrame?
The yarn you use for macrame is called macrame cord. You can use various materials such as cotton twine, hemp, leather or yarn, you can even.
How do I make macrame?
How to Make a Macrame DIY Wall Hanging STEP 1: Cut the Cord. First, you will need to measure out and cut all the cord for your project. STEP 2: Attach Cord To Stick. STEP 3: Create Triangle Using Square Knots and DHH. STEP 4: Spiral Knots. STEP 5: Finishing Off With Square Knots and Berry Knots.
What does saddle a dead horse mean?
To “saddle a dead horse” means to place u-bolts in the wrong spot. The cable has two parts – it’s end (called a dead-end) and the part that is attached to the load. The cable that attaches to the load should be on the bottom.
What is the saddle on a Crosby clamp?
When installing the clips, the saddle portion is placed on the load-bearing or live side. It is not to be placed on the non-load-bearing or dead side of the cable. This is to protect the stress-bearing end of the rope against crushing and abuse.
What is saddle clamp?
Saddle clamps are fittings that fasten to building walls, pillars and floors. They fasten metal pipes used for water or gas line installation, or resin cable conduits for electrical work. Different saddle band models can be selected to match different types, materials and sizes (diameters) of lines to fasten.
How do you crimp without a swaging tool?
Just crush the thing with any tool you have around. If you can use a big vise to crush them down, that’s probably the most ‘controlled’ way. Otherwise, use pliers, or get a hammer and chisel and dent the sleeve at two or three points with the chisel.
What is a swaging tool?
What are Swaging Tools? Swaging tools use pressure to expand or stretch the end of a piece of copper tubing so it can fit over another of the same diameter and make a permanent brazed connection. Often a flaring tool kit will come with swaging bits or die blocks to convert a flaring bar into a swaging bar.
How do you hide lamp cords in the middle of a room?
For cords that are still exposed, be sure you weight them down with a rubber cord cover (you can hide that further by applying contact paper, like wood-grain). Use baseboard clips or wall clips to affix cords to the wall or floor. It will help hide cords further and help eliminate tripping hazards.
How do you swag a pendant light?
– Swagging a Pendant Light Without a Chain – Mark on your line where you want the loop to go. Run the area where you want the loop over the thimble (the u-shaped device that makes the curve). Attach the clamp right below the thimble, and hand tighten it. Hang your light. Voila!.
Can you Mod Podge string?
As you wrap the string around the balloon, pull it through your fingers and squeeze some of the excess Mod Podge off. Pull the string taut around the balloon to help it stay put. When you pop it, the fun part, there will be excess Mod Podge left between the string.
How do you make a hanging yarn ball?
Instructions Blow up balloons to different sizes (filling balloons only halfway will help you achieve a more spherical shape) and knot each balloon. Create a drying area. Hang balloons from strings above the drying area. Spray balloons with cooking spray; this will make it easier to remove the yarn later.
How do you make a twine lantern?
Wrap some twine around the bottom tips of your balloons and hang them overnight to dry- I hung mine along my shower curtain’s railing. Allow them to dry for 24 HOURS. Once dried take your balloons twine fixtures down and take a thumbtack or something sharp to pop the balloon! BE GENTLE.
