Table of Contents
What does wide and sweep on epicenter?
The “Sweep” knob allows you to pick the center frequency that. you want The Epicenter bass restoration circuit to maximize. The “Wide” knob. adjusts how wide of a frequency range The Epicenter will effect.
How do you connect the equalizer to the epicenter?
We always recommend you put the Epicenter® BEFORE an EQ or crossover. Since the Epicenter is adding frequencies to your signal, you would want to put it before any EQ or crossover in order to be able to adjust those frequencies.
What does an epicenter do for car audio?
The Epicenter detects bass harmonics, then digitally recreates the underlying fundamental for the incredible punch and impact of live music. Your MP3 player thinks your car stereo is a pair of headphones, so it removes the bass!.
Why does my epicenter make noise?
This is most likely caused by not sending a full frequency signal to the Epicenter®. Did you connect the Epicenter to a dedicated sub channel? You need to send a full range signal to the Epicenter in order for it to perform optimally.
What is soundstream BX 108Z?
The BX-108Z has a unique equalization circuit that contours the restored bass to your speaker systems. Dash Mount Remote Control: The BX-108Z comes with Dash Mountable Remote Control allow you to enjoy the effects of the BX-108Z without leaving the driver’s seat.
How do I connect my equalizer?
Connect one pair of RCA cables between the receiver and equalizer. Connect one pair of cables to the pre-amp output channels on the receiver and the other end of the cable to the left and right channel inputs on the equalizer. You will usually find these channels on the rear of the equalizer.
How do you wire an equalizer?
To do so, connect a set of RCA cables to the head unit’s preamp outputs. Tape the RCA cables together to prevent them from separating. Run the RCA cables through the dash to the equalizer and connect them to the EQ inputs. Use additional RCA cables to connect the EQ to the amplifier (one set of RCA cables per amp).
What goes first EQ or crossover?
EQs and other devices should always be in Line before the actual Crossover. Most DSP Units offer Input EQ which is essiantially that.
What should the sweep be set at on a epicenter?
The “Sweep” knob allows you to pick the center frequency that you want The Epicenter bass restoration circuit to “maximize”. The “Wide” knob adjusts how wide a frequency range The Epicenter will effect. The effective range of the sweep control is 27Hz – 63Hz.
How do I adjust my Accu Bass?
How to setup AccuBASS® Set the AccuBASS Threshold dial all the way to the left (counterclockwise) Set the AccuBASS Level knob at the 12 O’clock position. Start playing a 50 Hz test tone. Slowly turn up the head unit volume until you start to hear bass dropping.
What does a bass processor do?
How a Bass Restoration Processor Works. adjustments: frequency, width, and level. The frequency adjustment allows you to choose the specific frequencies you would like brought out in your music. This allows you to have complete control over the bass in your system.
What is a synonym for epicenter?
attraction, lodestone. (also loadstone), magnet, polestar.
Why are my subs making a weird noise?
Subwoofer hum or buzz is a low-level noise that can be present whenever a passive or powered subwoofer is turned on, whether or not it is playing. This 60-hertz hum is a result of being plugged into an AC wall outlet. Usually, all it takes is a change in the way the subwoofer connects to power.
Why is my sub making a humming noise?
Why does my subwoofer make a humming noise? The voltage difference between a subwoofer electrical ground and the equipment ground can cause it to hum. This can happen because of the irregular current flow in your audio cable. Turning on the volume too high can also cause a hum.
What causes subwoofer thump?
This can indicate there is a failed diode / circuit in the receiver. You can have the receiver serviced but before going through that inconvenience try a couple things to minimize the problem. Adjust the gain control on the subwoofer in conjunction with the bass level control in the receiver.
How do you use Accu Bass?
For initial setup of AccuBASS: Turn the AccuBASS Threshold all the way to the left. Set the AccuBASS Level knob at the 12 O’clock position. Start playing music that is familiar and/or has a lot of bass. Slowly turn the volume up on the head unit until the bass starts to drop out (roll off).
Can you use an equalizer without an amp?
Car equalizer installation can be done as an independent process without necessarily having an amp installed. A well equalized car stereo will have superior sound even if not at extremely high volumes.
How do I connect an equalizer to an integrated amplifier?
Connect a pair of RCA cables from the preamp output of your integrated amp to the input on your equalizer. Connect a second pair of RCA cables from the output of your equalizer to the preamp input of your integrated amplifier.
How do you hook up stereo parts?
Plug in the audio cable into the CD player’s audio output (top picture) and then plug the other end into the stereo receiver’s CD audio input (bottom picture). 4. Run your speaker wire from the receiver to your speakers. Look for the speaker terminals (red and black) and stick the wire in there.
How do you connect an equalizer to a car battery?
How to Install a Stereo Amplifier & Equalizer in a Car Disconnect the negative battery cable (or grounding cable) from the battery. Connect the ring terminal from the amplifier wiring kit to the positive lead of the battery. Mount the amplifier and equalizer in the vehicle’s trunk.
How do you hook up a parametric equalizer to a car stereo?
Locate the wire going from the audio unit to your parametric equalizer, which should turn the power on your system and route it. Tie down this wire with whatever equipment or device in your car you think is appropriate. Then fasten the RCA cables from the dash unit to the preamp jacks.
