Table of Contents
Does a calcium reactor raise pH?
Often, it is easier to set the calcium reactor to keep parameters stable. Alternatively, you can use an extra reaction chamber, such as the Aquamaxx Effluent Chamber, which is a canister filled with calcium reactor media that will help increase pH of your effluent water before it is dripped back into your aquarium.
Do you need co2 for calcium reactor?
A calcium reactor uses carbon dioxide to melt old coral skeleton and enrich the tank water with calcium and alkalinity.
Is calcium reactor necessary?
Active Member. Anything under 100 gallons probably does not need a calcium reactor, as most experienced hobbiest either have really big tanks or really tiny, nano tanks. Unless your rock is bathed in sps coral, you do not need a calcium reactor.
Will calcium reactor lower tank pH?
A calcium reactor will drop your aquarium pH. The very nature of dissolving limestone and aragonite using carbon dioxide means that the effluent water going into your tank has a very low pH.
Does a calcium reactor add alkalinity?
In marine and reef aquariums, a calcium reactor creates a balance of alkalinity. An acidic solution is produced by injecting carbon dioxide into a chamber with salt water and calcium rich media.
How does a kalkwasser reactor work?
The way a Kalkwasser Reactor works is quite simple as they essentially are just a mixing chamber for RODI water and Calcium Hydroxide. The clear solution that resides on top is then dripped into your aquarium based on your tanks demand for calcium and alkalinity. If you need more calcium, increase the drip rate!.
What is the pH of ARM media?
Valuable Member. I keep mine set to 6.6-6.8 pH. I’ve had mine as low as 6.5 with no problems.
Why do you need CO2 for a calcium reactor?
Injecting CO2 lowers the pH of the aquarium water inside the calcium reactor just enough to dissolve the calcium reactor media and enrich the water. This acidic water is enriched with calcium, carbonate alkalinity, strontium and trace elements.
How long does CO2 last calcium reactor?
Under normal usage, a 5 lb CO2 bottle lasts 6-12 months; media lasts approximately 6 months before needing to be replaced. While the initial investment of a calcium reactor may be a high, the long-term costs are very inexpensive.
How much flow does a calcium reactor need?
Flow Rate – Flow rate should be set at 1-2 liters per hour, depending on the aquarium size, through the reactor. The flow rate can be increased or decreased to adjust calcium levels in your aquarium.
Do I need a reactor in my reef?
They are a very effective way of ensuring your tank inhabitants, such as corals and clams, have the elements they need to maintain peak health in your reef. Media Reactors are exactly as they sound. Every carbon has the potential to release phosphates into an aquarium, because all carbon is a chemical element.
What is a nitrate reactor?
Nitrates are the bane of every fishkeeper and Nitrate Reactors are used to introduce nitrate-battling biological media to your fishtank. They are used for either freshwater or marine aquariums. When there is an absence of oxygen the bacteria that causes nitrates is allowed to flourish.
How does a phosphate reactor work?
A phosphate reactor is a useful filtration add-on often employed for the small reef aquarium. Without a phosphate reactor, phosphate levels would naturally rise, as phosphates are a byproduct of fish foods. Unchecked, they can rise to levels that are deleterious to any organism that relies on calcification.
When would you use a calcium reactor?
If your corals are beginning to outgrow your aquarium and you’re considering moving to a bigger tank, that’s an ideal time to work a calcium reactor into your new & improved reef aquarium system. There’s no reason you can’t set up and run a calcium reactor from the start of a new tank.
What does calcium reactor do?
A calcium reactor creates the effluent solution by lowering the pH of the water inside the reactor with dissolved CO2 until the calcium carbonate media or old coral pieces dissolve and enrich the water with calcium and alkalinity.
What is the unit of alkalinity?
The unit of measurement for alkalinity is mg/L CaC03. What is the significance of alkalinity? Alkalinity is the measure of the resistance of water to the lowering of pH when acids are added to the water.
How do you put kalkwasser on top of the water?
Start by filling your top off container up with RO/DI water. Then measure your dry kalk powder (recommended to start at 1/2 teaspoon per gallon of water, max dose of 2 teaspoons per gallon). Pour the powder into your top off container and gently mix with the spoon.
What is Armmedia?
About Us. ARM Media Group is an entertainment rights management company that owns and controls libraries of sound recordings on a global basis.
How long does a 10lb CO2 tank last Aquarium?
10lb. Co2 tank. lasts about 9 months.
Is a media reactor necessary?
Media reactors just hold media (GFO, GAC, biopellets, etc). You only need a media reactor if you need one of those types of media. So the real question should be if you need GFO, GAC, or any other media that might fit into a reactor. The answer depends on how your tank behaves after it’s up and running.
What do reactors do in reef tank?
Aquarium media reactors greatly improve the efficiency of filter media inside it by increasing the surface area and contact time between the media & the aquarium water as it is pumped through it. These simple containers allow easy mounting, cleaning and can be used singularly or mulitple together.
What does a carbon reactor do in a reef tank?
These multi-purpose in-sump media reactors can be used with carbon and GFO to help eliminate organic pollutants, odors, discolorations and algae fueling elements within marine and reef aquaria.
Do nitrate reactors work in freshwater?
They work in both freshwater and saltwater aquariums and do a great job. Because it is a bio-ball based media, it is best run in a media reactor versus a canister filter or power filter. It will still do the job in any of them, it’s just more effective in a media reactor.
