Table of Contents
How do you cut vinyl on Silhouette Cameo?
Step One: Cut Out Vinyl Open design in Silhouette Studio® and resize as desired. Select your type of vinyl from the material drop-down list in the Send panel. Load the vinyl into your Silhouette. After your image is cut, remove the vinyl from your Silhouette.
Which side of vinyl goes down on Silhouette Cameo?
This is one of the most common reasons the Silhouette CAMEO isn’t cutting. Place the vinyl onto the Silhouette Cutting mat with the backing (paper) side down onto the mat making sure the vinyl is covering the same area where the design is placed on the virtual mat in Silhouette Studio.
How do I start cutting on my Silhouette Cameo 3?
Here is what you want to do to get ready to cut: Remove the mat from the bag. Then gently peel back the paper from the mat. The mat is VERY sticky. Place the paper inside the grid guidelines. Use your palm or a Silhouette scraper tool to make sure the paper is stuck down to the mat evenly across the paper.
Do I need to use a cutting mat with vinyl?
Lined materials are the only materials that can be cut without a cutting mat. These are materials such as adhesive vinyl, heat transfer vinyl, and stencil material. These materials are on a liner which is eventually removed after cutting. This is why paper always needs to be cut with a cutting mat.
Which side of vinyl do you cut?
The clear carrier sheet is the “shiny” side. The shiny side goes down when your cutting. The vinyl side goes face up. You want to cut through the vinyl, but not through the carrier sheet.
What silhouette blade do I use for vinyl?
With the exception of fabric, the ratchet blade is used to cut all materials, ranging from paper to vinyl to stencil material, etc in the CAMEO and Portrait. It is used on the same materials in the CURIO.
What is the difference between cut and cut edge on silhouette?
Cut means that it is going to cut around each object on the screen. If the design is overlapping, then it is going to cut through each piece. Cut Edge means that it will cut around the outside edge of any objects that are overlapping.
Why won’t my silhouette cut heat transfer vinyl?
The most common cause for the Silhouette CAMEO 3 not cutting or not cutting through is a problem with the blade – specifically the Autoblade. In addition, make sure the blade is locked into place. When it’s locked the circle on the locking tab will turn dark green.
What setting to cut oracal 651 on silhouette?
Cut your design- You can cut your design by hand or use a craft cutter. After your design is all cut, remove the excess vinyl from around your image/lettering (this is called weeding).Silhouette Cameo: Speed: 7. Thickness: 5. Blade Setting: 2.
What’s the difference between oracal 651 and 631?
The main difference between 651 and 631 is going to fall in the adhesive on the vinyl and the finish on the vinyl. Oracal 631 has a matte finish on it – meaning it does not have the glossy sheen to it, it also has a lighter adhesive so it is best used indoors and can be removed faily easily.
What side do you cut 651 vinyl on?
The shiny white vinyl side should face up. The grided paper side that says Oracal faces down. This is normal 651 vinyl. HTV is the one that gets cut upside down.
How big can a cameo 3 cut?
Silhouette CAMEO 3 desktop cutting system Silhouette CAMEO ® Specifications: Maximum Cutting Area 12 in. x 24 in. (30.5 cm x 61 cm) with a cutting mat 12 in. x 10 ft. (30.5 cm x 3m) with a lined media Maximum Media Thickness 78.75 mils (2 mm) Maximum Cutting Force 210 gf USB Port For reading and cutting saved files directly.
Why is my silhouette cameo 4 cutting off the mat?
The cutting mat settings in the software do not match the actual set up. The mat or material is not being loaded properly. The material is not being loaded placed properly onto the cutting mat or is in the wrong orientation.
Can you use a silhouette cameo without a mat?
Remember you can only cut lined materials like vinyl, heat transfer vinyl, or stencil material without a cutting mat. The Silhouette CAMEO and Portrait machines can cut up to 10′ long so the height can be adjust up to 120″.
How do you use the 4 mat on the Silhouette Cameo?
Here’s how it works. With the CAMEO 4 powered on, press the load button (up arrow) on the front panel. The button will start flashing. You now have 3 seconds to line up your cutting mat (covering the mat detection sensor) and then the machine will automatically feed the mat in.
Do you take the backing off vinyl before cutting?
You want the blade to cut through the vinyl cleanly without cutting through the backing. This is called a “kiss cut,” and it will make it much easier to weed and apply your decal in the next steps.
Do you peel the back off vinyl before cutting?
Gently peel the transfer tape from the paper backing at a 45-degree angle. If the vinyl does not transfer to the tape lay it back down and burnish it again. Now, it’s time to clean the surface that you’ll be applying the vinyl to.
Can you use ratchet blade in cameo 3?
When loading the Black Ratchet Blade into the machine, ensure that the little “fin” at the top of the blade is facing you, then lock the blade into place. The Black Ratchet Blade can be used in the Silhouette SD, Silhouette Portrait, Silhouette Curio, and Silhouette Cameo 1, 2 and 3 machines.
