Table of Contents
What tool cuts tongue and groove?
Tongue-and-groove joints are commonly made on a table saw. But with the right bits, the joints can be made just as easily on a router table.
Can you cut tongue and groove with table saw?
To produce a tongue and groove on the table saw, use a dado cutter rather than your everyday blade (unless your stock is 3⁄8″ or less in thickness). I use the two outside cutters to produce a 1⁄4″ cut width when working 3⁄4″ stock. Thicker stock calls for a wider groove.
Do you cut the tongue or groove first?
Step 1: Generally speaking, it’s easier to cut the groove of a T&G joint first, then mill the tongue to fit the groove. A 1/4-in. straight bit or spiral upcut bit makes an ideal groove-cutter into the edge of a workpiece.
Should tongue and groove be glued?
The recommended glue for floating installation is Tongue and Groove engineered flooring glue. Glue placement is very important. The glue must be placed along the topside of the groove the full length of the grooved side and end.
How deep should a tongue and groove be?
The groove should ALWAYS be slightly deeper than the tongue is long, by as much as 1/16″ for 3-inch wide boards. The reason for this is two-fold.
What tool cuts grooves in wood?
A router is a handy tool to have, being used for cutting grooves (properly called rabbeting), cutting slots in boards, such as for hanging them, trimming the edge of laminate, and cutting various types of tongue and groove joints for putting pieces together.
Is a router plane useful?
Router planes, which are more like shoulder planes than routers, are invaluable for cleaning up and trimming tenon cheeks and other joinery, hinge mortises, inlay mortises, and more. But to do its best work, this small plane must be properly tuned. Learn how to get it that way, and how best to use this handy plane.
What is a shiplap joint?
A Ship Lap joint is essentially two opposing rabbet joints that overlap each other to hold panels together. It is used in furniture for drawer bottoms, tool chest bottoms, and the backs of cabinets. It is also commonly found in the construction of barn walls.
Do you nail the tongue or groove?
For tongue-and-groove flooring, drive a nail at a 45-degree angle through the tongue, then conceal it by engaging the groove of the next board. Be sure to countersink the nail — drive it slightly below the surface of the wood — to prevent interference in the joint.
Does the tongue or groove go against the wall?
Which to Install First. Which side is the tongue, which the groove, and which goes first during installation? The tongue is the side that you will want to place against the wall as you start your laminate-flooring installation.
Can a router cut tongue-and-groove?
When it comes to cutting the joint, the router table makes quick and precise work of the job, thanks to router bits that cut complementary tongues and grooves. Think of it as cut ‘n go: Rout each edge, and you’ve made a perfect joint.
Can you use a brad nailer for tongue and groove?
A finish nailer or brad nailer is the easiest and most efficient tool to use when installing your new shiplap or tongue and groove. They can be purchased/rented relatively cheaply from your local hardware store, they’re lightweight, and are simple enough that a 12 year old can use them!Nov 21, 2020.
Where do you nail your tongue and groove?
Avoid visible nail holes Install planks with the tongue up. Nail at an angle directly through the tongue and into your studs. You don’t need to nail through the face of the planks anywhere but on the bottom row and near the ceiling. Start with the bottom row first and work your way up.
How long does tongue and groove glue take to dry?
Remove excess glue immediately. Once dry this adhesive is highly water resistant. Allow 24 hour drying time before subjecting flooring to normal traffic. Clean Up: Fresh adhesive – Damp cloth and water.
Can you install tongue and groove over drywall?
Installing tongue-and-groove (aka T&G) boards is a fast, inexpensive way to panel any ceiling or wall. You can install T&G over bare framing, drywall or plaster, so it’s a great cover-up for an ugly ceiling.
Can you nail hardwood on the groove side?
To nail the groove, you must nail by hand, but you have a very small space in which to work. In addition, you must countersink every nail to avoid interfering with the tongue of the next plank. For most applications, this isn’t feasible or desirable.
What is the difference between mortise tenon or tongue & groove?
The mortise and tenon joint is to introduce rigidity and strength to wood joinery and are connected at right angles. Whereas the tongue and groove joint is joined in parallel wood pieces (thus the need for a longer area for joining).
Are tongue-and-groove joints strong?
A tongue-and-groove is stronger than simple butt joints due to the increased gluing surface and mechanical interlocking of the two mating pieces. As a bonus, the tongue also serves to perfectly align the workpieces during the glue-up for a smooth surface.
How thick is tongue-and-groove?
STEP 1: The usual convention for building tongue-and-groove joints is to cut the groove (or dado) first, then mill the tongue to fit it. Although the proportions of the joint parts can vary, usually the width of the groove is 1/3 the thickness of the mating part. So, on 3/4-in. stock, make your groove 1/4-in.
How do you measure tongue-and-groove?
How to Calculate Tongue and Groove Flooring Divide the floor area into rectangles. Measure the width and length of each rectangle. Multiple the width by the length for each rectangle to determine the surface area. Determine the area of an individual piece of tongue and groove flooring.
