Table of Contents
How do you cut a plywood floor?
One method is to use a small hole saw and drill around the nails, just the thickness of the floor. Then (after getting the sheet of plywood up) you end up with a bunch of small plywood plugs you can break off the screws/nails fairly easily, and enough nail/screw to get a grip on for removal.
Can you replace sections of subfloor?
Cutting out a section of subfloor starts with removing the flooring and any plumbing fixtures at the affected area. Making precise cuts allows you to replace the section without installing additional backing or blocks at the floor joists.
What kind of saw will cut close to a wall?
A toe-kick saw is basically a circular saw with an extended arbor on which the blade is mounted. It is used to cut the tiles, luan, vinyl (or similar sub-floor materials) under the kick space close to the cabinet base. You can also use it to flush cut tiles closer to walls and cabinet base.
Will an oscillating tool cut plywood?
HCS Japanese Tooth Oscillating Blade This blade can make the smoothest and most accurate cuts out of all oscillating tool blades. It uses its extremely sharp teeth to aggressively cut through wood, plywood, particle board, plastic, sheetrock, drywall, fiberglass and other non-metallic materials.
Can an oscillating tool cut wood?
The oscillating multi-tool is one of the handiest tools you can have around the jobsite or workshop. Its versatility lets you accomplish numerous tasks that would be impossible with other tools. You can sand; saw metal, wood, and drywall; make large holes; plunge cut into hardwood; or undercut a doorway.
What is an undercut saw?
An undercut saw is a tool used in woodworking and construction. An undercut saw is very similar to a standard circular saw. In fact, it essentially is an upside down circular saw. Although it is used to cut materials, an undercut saw has a slightly different function and purpose than a standard circular saw.
How do you fix water damaged subfloor?
How to Fix a Water-Damaged Subfloor: Your 8-Step DIY Guide Start by Stopping the Water. Expose the Subflooring. Make Your Mark. Carefully Cut Subflooring. Remove Damaged Materials. Speed Up the Drying Process. Reinforce Floor Joists. Install Your New Subflooring.
How do you fix an uneven subfloor?
For concrete slabs: If there are only a few problem areas in the concrete, you can mechanically flatten them by grinding, bead-blasting, abrading, or using a patching compound. If the entire slab is uneven, you may have to use a self-leveling concrete compound to smooth it out.
Can you lay new subfloor over old subfloor?
One of the benefits of removing the old flooring is it allows you the chance to fix any loose subflooring or squeaks by re-securing the main subfloor to the floor joists prior to installing the new flooring. With all that being said though the answer is YES you can install New Wood Flooring over the old.
Does the subfloor go under walls?
Wall and Floor Basics Subfloor: The subfloor is nailed to the top of the joist. Often 19/32-inch to 1 1/8-inch thick plywood or OSB, the subfloor might run continuously across the joist, or two sections of subfloor may meet on a joist. Bottom Wall Plate: The bottom wall plate is the bottom-most part of the wall.
Can you cut laminate flooring with a knife?
A regular utility knife blade can be used to cut flexible, self-adhering laminate strip material. The caveat is that you must change the blades frequently so the knife cuts properly — a dull blade will not cut effectively.
How close can a concrete saw cut to a wall?
“We can cut through a 10-inch thick wall with a 14-inch blade,” says Zoni. “You can only cut 5-1/2 inches with a 14-inch blade on a cut-off saw.” A 2 x 4 shot into the concrete wall guides the smaller saw along the cut.
How close can a toe kick saw cut?
Maximum clearance of this tool under toe kicks is 3 1/2 inches combined with a maximum cut depth of 3/4 inch. In earlier days the only solutions for removal that this wonderful power tool provides, was either removal of cabinets or painstaking hammering and chiseling to remove the underlayment.
How do you cut concrete against a wall?
Use a standard circular saw, equipped with a corundum or diamond blade, for small tasks. For slabs, it’s best to cut through the top inch, then use a sledgehammer to break off the rest. The jagged edge left below the cutting line provides a good rough edge for the new concrete to bond to.
What tool do I use to cut paneling?
For precision cutting and detail work, the best way to cut paneling is with a sabre saw with a fine tooth blade. It is fast and easy, but a sabre saw is extremely difficult to keep in a straight line when free-handing.
How do you cut wood paneling on the wall?
Circular Saw To keep from splintering the finish surface of the paneling, cut from the backside. Paneling blades are available for circular saws, or you may use a fine-tooth wood blade. Set the blade depth to the thickness of the paneling and use sawhorses and a sheet of plywood to make a cutting table.
How thick of wood can an oscillating tool cut?
How Deep Can an Oscillating Tool Cut? Oscillating tools can cut as deep as their blade is long. That’s typically between 1 and 3 inches.
How do you cut wood straight with a multi-tool?
How to Cut Straight. To create a straight cut, a round or half-moon saw blade works best. You want to lightly press down on your tool creating a cut no more than 1/4 inch deep. Run your blade across the length of the cut multiple times with each pass making it a little deeper until you cut through your material.
What do you use a oscillating tool for?
What is an oscillating tool used for? Trimming pipes and screws. Plunge cuts in your decking. Trimming wood and floorboards. Cutting out openings in drywall. Removing rust from metals. Sanding down furniture. Scraping adhesive. Removing mortar.
