Table of Contents
Here are a few alternative methods that you can use to cut or break wiring on a job without using wire cutters. 1 – Bend it. If the wiring in question is on the thinner side and relatively pliable, you could try bending it. 2 – Hacksaw. 3 – Tin Snips. 4 – Reciprocating Saw. 5 – Angle Grinder.
What is the best tool to cut wire?
The Best Wire Cutter Our pick. Channellock E337CB Diagonal Cutting Plier. Strong cuts, comfy grips. Budget pick. Irwin Vise-Grip 2078306 6-Inch Diagonal Cutting Pliers. Quality at a bargain. Also great. Bahco 2101G-180 Ergo Cutting Pliers. Great features, not as strong. Also great. Klein 11054 Wire Stripper-Cutter.
What tool is used for cutting wire only?
Diagonal pliers (or wire cutters or diagonal cutting pliers or diagonal cutters or side cutters) are pliers intended for the cutting of wire (they are generally not used to grab or turn anything).
How can I cut wires without a wire cutter?
Here are a few alternative methods that you can use to cut or break wiring on a job without using wire cutters. 1 – Bend it. If the wiring in question is on the thinner side and relatively pliable, you could try bending it. 2 – Hacksaw. 3 – Tin Snips. 4 – Reciprocating Saw. 5 – Angle Grinder.
Can you use pliers to cut wire?
Diagonal cutting pliers have a sharp, rounded tip, making them great for stripping and cutting wire. You can use these for nearly any type of wire. Diagonal cutting pliers are also widely used for removing pins and nails as well. If you want to cut a wire hanger, for example, this is a good option.
What do wire cutters look like?
Flush cut wire cutters (also called “combination” or “lineman’s pliers”) look like an ordinary pair of pliers but feature a pair of cutting blades flush to the outside edge and directly behind one of the plier’s gripping jaws. However, they may require more manual force to cut the wire than diagonal cutters.
Can pliers cut metal?
There are a number of pliers that are designed with a cutting blade that will allow you to cut metal or wire, including the standard model pliers. The cutting edge of the pliers is normally located in the back of the jaws and has a serated or sharpened edge, allowing you to cut the metal without too much trouble.
Is it safe to cut wires?
A: Cable and phone wires don’t carry current, so it’s safe to remove them. However, it’s critical not to cut into a power line, as you know.
Can scissors cut braces wire?
In certain cases, the wire can be carefully cut with a nail clipper or fingernail scissors. If you cut the wire, make sure to hold one end of the wire or place a tissue or piece of gauze around it so it can be removed from the mouth.
What is used to cut thick wires?
Best Wire Cutters When it comes to cutting wire, a standard pair of pliers will cut some types, but any professional will tell you there’s nothing quite like having the right tool for the job. It makes life easier and gets the work done faster. If you need to cut wire, you need wire cutters.
How do you cut electrical wires safely?
Use a utility knife to rip round cable. Carefully follow the wire’s contours to avoid cutting or nicking the wires inside. When ripping either kind of cable with a utility knife, always work on a flat horizontal or vertical surface and cut away from your body, never toward it.
How do you cut thick copper cable?
Tools for Cutting Medium Gauge Copper Wire A good heavy pair can cut copper wire up to 1/4 of an inch thick. Coax cable cutters are designed for cutting multipair wiring. With a curved blade, these cutters are good for insulated cables and small braided wire. Diagonal cutters are great for cutting in tight situations.
How do you cut a flat ribbon cable?
It is typically used in electronics. To trim ribbon cable to size, use a scissors; the blades of a wire cutters are often too short. If there is a connector attached to the cable, you may need to remove it before cutting. Hold onto the connector and pull the cable backward to pull it away from the connector.
What are flush cutters?
Flush-cutters – provide an unbroken, even cut to the material for a clean design look. Because the jaws are angled, both ends of the wire cannot be cut flush, only the wire on the side that is flat will be flush, the wire remnant on the angle side will have an angle or “V” cut.
How do I choose a wire cutter?
Wire Cutter Selection Guide Cutting Capacity. The cutting capacity tells you what size wire can be cut and will be rated according to either the wire gauge or the diameter of the cable (not including the thickness of the insulation). Blade Material (Hardness) Handle Length (Leverage) Insulated vs.
How do you cut a piece of metal?
An angle grinder fitted with an abrasive metal-cutting disc works well to cut all kinds of metal, including bolts, angle iron, rebar and even sheet metal. But the discs wear down quickly, cut slowly and shrink in diameter as you use them. Instead, we recommend using a diamond blade that’s rated to cut ferrous metal.
How do you smooth out the ends of a wire?
Sharpening Stones and Files: Rub a small drop of sewing machine oil on the stone and gently drag the wire end across the stone. Twist the wire around and repeat. Keep twisting the wire end around so the complete circumference of the wire end has been smoothed.
Can you sand down wire?
Yes, like EightCloudyCupcakes suggested, sand paper or a nail file might do the trick.
Are pliers the same as wire cutters?
Remember that wire strippers are best for removing the insulation from wire, while cutters are best for (you guessed it) cutting wire. Pliers help you reach, bend, grab, cut, hold and loop wire, and crimpers are the best tool to join two pieces of ductile material together.
What is the difference of scissors and wire cutters?
It can cut copper and stainless steel braid without damage. The blade of regular scissors is not designed for cutting metal messes. On the other hand, the blade of a regular wire cutter does not cross each other. There is always a small gap when fully closed.
