Table of Contents
What saw to cut laminate countertop?
To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front.
Do you need a special blade to cut laminate countertop?
Cutting a post-form laminate countertop to length requires a clean, straight cut. The best DIY tool for the job is a circular saw with a fine-tooth carbide blade made for laminate (the same blades are typically sold for non-ferrous metals and other types of plastics). You can also use a jigsaw with a fine-tooth blade.
How do you cut laminate countertop without chipping?
How do you cut down a laminate countertop?
Attach a fine tooth blade to a jigsaw, and then use the saw to cut through the countertop along your drawn cutting line. Keep the saw going straight along the rear of the counter, removing the upturned section of the backsplash while leaving the laminate that covered the section untouched.
How many teeth do I need to cut laminate?
Blades for Laminate Flooring Interestingly the same aluminum oxide is used to make industrial grade sandpaper! In view of this, a thin kerf, 80 to 100 tooth, carbide-tipped blade is most effective for cutting laminates and will last for about 1000 sqft before needing to be re-sharpened.
Which side of laminate do you cut?
Cut the First and Last Rows In fact, you can cut the planks using a table saw, miter saw, circular saw, hand saw or laminate cutter. However, using a diamond blade is recommended as laminate can be tough to cut through and may damage another type of blade. Typically, you will cut with the finished side up.
What is the best tool to cut Formica?
Use a circular saw or laminate shears to cut the Formica into large pieces. Do not try to cut a curve with a circular saw. Cut out the shape’s form, and leave the trimming for a finer saw and corners for a saw with a some flexibility.
Can you cut laminate countertop with a utility knife?
Circular Saw or Track Saw are the best tools to cut Formica. The power of both saws can cut through the thin and thick layers of Formica. Can You Cut Laminate Countertop With A Utility Knife? Yes, you can cut laminate countertop with a utility knife.
Can you cut the back off a laminate countertop?
Normally, the backsplash is cut before it is installed. Before installation, you can set the laminate piece on two sawhorses for cutting. If the laminate is already installed, you can still cut it down but the wall texture underneath the laminate will probably need to be refinished afterwards.
Do you have to cut the tongue of the first row of laminate?
Place the first plank with the tongue side towards the wall, being sure to allow 1/8″ for expansion. We recommend cutting off the tongue on this first row to avoid any problem with the expansion gap. If it is too short, cut a new plank in half and use one half to start the second row.
How many teeth saw blade for laminate?
Diamond-tipped blades that are made for laminate and fiber cement usually have a low number of teeth to reduce the dust produced by cutting cement. However, typical circular and miter saw blades that are used for laminate will have 80 to 100 teeth for fine, precision cutting.
What is a 40 tooth saw blade used for?
Crosscut blades, made for cutting across the woodgrain (across the face of a board), have between 40 and 80 teeth and are designed for clean cuts. Smaller gullets separate the teeth. Combination blades can make both rip cuts and crosscuts.
Can I cut laminate with a jigsaw?
Jigsaw: A jigsaw is a real all-rounder when it comes to cutting laminate floors. It’s best used to cut out shapes from your board. For example, when you want to place boards around your toilet or maybe a pillar.
Which side of laminate goes against the wall?
The tongue is the side that you will want to place against the wall as you start your laminate-flooring installation.
Can you cut Formica with a table saw?
You can use any type of saw blade to cut a laminate countertop with a table saw but some people like using a carbide blade, fine tooth blade, or a jigsaw blade. Carbide-tipped blades and fine-tooth blades will give you the most accurate cuts and are more durable than other types.
Can you score and snap Formica?
Move the laminate so that the score mark is aligned with one edge of your work table. Lift up on the end opposite the piece you will be using. Snap it downward to break the laminate along the score line. Set the unused portion of the laminate sheet aside.
Can you cut laminate with a razor blade?
Vinyl tile cutting boards will also cut laminate tile material, since vinyl and laminate are similar. The blade on the tool is essentially a large razor blade installed on a board that has a leverage bar attached. When pulled or pushed, this lever presses the blade down, forcing it to cut through the laminate tile.
Can a Dremel cut laminate countertop?
The 565 Multipurpose Cutting Kit allows for sturdy, controlled cuts in a variety of materials, including drywall, laminate, fiberglass, plastic and vinyl siding. The easy screw-on mounting system allows you to install the Dremel cutting kit to your rotary tool in seconds.
