Table of Contents
How to Cut a Concrete Curb Mark the area you wish to saw with a bold piece of colorful chalk. Start the saw and begin to cut with a 45 degree angle at the top of the curb. Cut slowly letting the blade do the work. Follow the chalk line with the blade of the saw until you reache the bottom.
What can I use to cut concrete curb?
Use a standard circular saw, equipped with a corundum or diamond blade, for small tasks. For slabs, it’s best to cut through the top inch, then use a sledgehammer to break off the rest. The jagged edge left below the cutting line provides a good rough edge for the new concrete to bond to.
Can you cut concrete with an angle grinder?
Although the various concrete cutting saw is available, an angle grinder is the most convenient tool for small concrete cutting work. A concrete-cutting blade for an angle grinder has a diamond-studded rim with ventilation grooves — a tile-cutting blade uses diamond studs but does not have the grooves.
Can you cut into a curb?
It is unlawful for any person to cut, break or remove any curbing or sidewalk, or cause to have cut, broken or removed any curbing or sidewalk, or to install, or cause to be installed, any driveway, on any public street in the city, without first obtaining a permit to do so from the superintendent of public works in Jul 26, 2021.
What is a driveway apron?
What is a driveway apron? It’s the area where your residential driveway meets the street pavement. You can transform that plain patch of tarmac by tearing up the section above the curb and replacing it with materials that look like they were taken from the streets of Brussels itself.
What is the dip in the sidewalk called?
A curb cut (U.S.), curb ramp, depressed curb, dropped kerb (UK), pram ramp, or kerb ramp (Australia) is a solid (usually concrete) ramp graded down from the top surface of a sidewalk to the surface of an adjoining street.
How do you grind down a driveway curb?
Cut many parallel kerfs in the curb with a diamond blade in a Skilsaw or an angle grinder. You can buy such a blade for only a few dollars at your local home center. Make these kerfs no more than about 1/2 inch apart, and slope the depth of the kerf so that the cuts are deepest at the street.
Can you cut concrete curb?
Concrete-cutting services make the cleanest cuts. If you do the cuts, use a large, hand-held, gas-powered concrete-cutting circular saw (with diamond-carbide blade) from a rental center. The blade should be at least 14 inches (35 cm) in diameter, which allows you to cut curbs up to 6 inches (13.7 cm) tall and wide.
How much can a concrete grinder remove?
How much will a concrete grinder remove? A grinder can take off up to 1/8 of an inch of material with each pass — less than a concrete scarifier, which cuts into surface coatings and the underlying concrete and can cut about 1/4 of an inch with each pass.
Can concrete be shaved down?
Yes, all concrete can be polished. Any pre-existing concrete can be ground down and smoothed with the right devices and skills. But, the ease and difficulty of the concrete grinding can vary depending on how old the slab is.
How do you cut concrete by hand?
Use your dominant hand to grip the back handle and push the blade forward and backward. Begin cutting at the edge of the concrete and slowly follow the chalk line. Don’t press the blade into the ground—let the weight of the blade and saw do the work. Remove the blade every 30 to 45 seconds to avoid overheating.
Can a Dremel cut concrete?
Dremel 545 and EZ545 are both diamond wheels great for cutting, sawing and carving hard materials; such as, marble, concrete, brick, porcelain, ceramics, hard epoxy and soft and hard wood. Do not use them on metals.
Will a metal grinding wheel on concrete?
Wheels intended for use on masonry are made with a silicon-carbide abrasive. Metal-cutting wheels contain either zirconia or aluminum oxide, depending on their intended use. Silicon-carbide abrasive particles are sharper and harder, and thus continue cutting efficiently on concrete or other masonry surfaces.
How do I get a curb cut in NYC?
Curb Cut Permits & Your Project Complete the work permit application, and submit the required documents through DOB NOW: Build. Obtain the Department’s application approval. File for and pull all construction permits. Complete the work. Close the curb cut construction process.
How thick should a driveway apron be?
Acceptable material—concrete is the most common, followed by asphalt, and then pavers. The thickness of the apron. For example, concrete on the non-apron portion of the driveway should be a minimum of four inches thick, while codes may require the apron portion to be as much as seven inches thick.
What do you call the grass between the sidewalk and the street?
A road verge is a strip of grass or plants, and sometimes also trees, located between a roadway (carriageway) and a sidewalk (pavement). Verges are known by dozens of other names, often quite regional; see Terminology below. The land is often public property, with maintenance usually being a municipal responsibility.
Who owns the space between the sidewalk and street?
Generally, no, but the property owner is responsible for maintenance. This usually includes the side walk (but not the curbing, if present.) Some municipalities have a cost sharing agreement for sidewalk replacement. A few years back, the city came through and tagged all of the sidewalk sections that needed replacing.
