Table of Contents
Do you have to cut tile around toilet?
They often ask if they should remove the toilet before installing a new bathroom floor. While it is possible to install a new linoleum or ceramic tile floor without removing the toilet, it is not recommended and actually can increase the labor involved in the project.
Should the toilet flange be flush with tile?
The bottom of the flange must be flush with the tile, no gaps, or it could end up too high. You don’t want a large wax depth from having it too low and if it is too high, the toilet will rock. The seal is engineered to work best with the flange on top of the finished floor.
Can you cut tile that is already on the wall?
Cut ceramic tiles already in place with am angle grinder and diamond blade. Once you glue ceramic tile onto a wall, it’s generally there to stay. Cutting through the tile with an angle grinder or rotary tool allows you to separate the unwanted portion of the tile from the wanted portion.
Can I cut tiles with a multi tool?
For some DIYers, an oscillating tool is among the best tools for cutting tile. An oscillating multitool can replace a tile nipper (since it also works by cutting the tile edges to shape it) but cannot replace a manual tile cutter or a wet tile saw and other tile cutting tools.
How close should tile be to toilet flange?
When you’re tiling around an already-installed toilet, plan out your pattern so that at there is at least 2 in (5.1 cm) of space between the base of the toilet and the edges of any of the tiles you’ll be laying around it.
How far above tile should toilet flange be?
Check the Flange Height The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
Can a toilet flange be flush with the floor?
When you install your toilet flange, it should be installed on top of the finished floor, and it should also be installed perfectly level. If your flange sits even or below the floor, then it’s wrong. It has to sit evenly on top of the finished floor. As a result, the toilet may wobble or leak at the base.
What causes tile to chip when cutting?
If a tile chips, it is generally not a manufacturing fault but is the cause of one of the following accidents against the tile itself: Dropping a heavy or hard object onto the ceramic or porcelain tile. This may cause the surface to crack or chip.
Do you cut ceramic tile face up or down?
Regardless of the kind of tile you’re cutting, the best method is to cut with the front of the tile facing up. The front is the side that will be exposed once you lay the tile. This method ensures the smoothest finished edge on the tile with the least amount of chipping.
Can a Dremel Multi Max cut tile?
The Dremel MM485 carbide flush cutting blade is the first oscillating cutting blade with high-performance carbide teeth. Now users can cut hardwoods, nails, screws, stainless steel bolts, galvanized pipe, plaster and lathe, cement board, fiber board, sheet metal, slate, ceramic wall tile and more.
What saw blade to cut ceramic tile?
The Blade. The best type of blade to use with an angle grinder when cutting ceramic tile is a diamond-tipped, smooth-edge blade without any notches or serration. Notched blades are for porcelain and serrated blades are more suited to natural stones.
Can a toilet flange be too high?
When your toilet flange is too high, your toilet may leak water and rock back and forth when used. Both the leaking and the rocking can warp or break the floor. A leaking flange can also rot the subfloor and lead to the accumulation of mildew and mold.
Can a toilet flange be too low?
Low toilet flange is a common problem when installing a new (or in my case thicker mortar base). Unless your toilet is properly mated and sealed to the waste pipe, you may face problems related to sewer gas odor (it’s very unhealthy and unpleasant) and/or fluid leaks.
Does toilet flange need to be secured to floor?
The flange should be fastened to the floor. Dry fit the toilet to make sure it doesn’t rock. If it does rock, use shims to prevent rocking – just tightening the bolts probably will not stop the rocking but will risk cracking the toilet or breaking the flange.
Can you install a toilet on top of vinyl plank flooring?
It’s considered best practice to always put a toilet on top of the flooring, whether the floor is made of wood, vinyl, tiles, etc. Not only will placing the toilet on top of the vinyl plank flooring generally look better, but it also ensures that the weight of the toilet is held by the floor and not the pipes.
Do you have to remove toilet to install laminate flooring?
If you’re installing a new floor, pedestal sink, and toilet, you should install the laminate flooring first so it’s under the sink and toilet. Because laminate flooring floats above the sub-floor on top of underlayment, it will expand and contract slightly with the temperature and humidity of the room.
Will a Tapcon bit drill through tile?
They don’t work on porcelain tiles, too hard. Tried masonry bits too. Basically that’s what Tapcon bits are, no go either.
What screws for toilet flange tile?
I use deck screws for setting those, usually 1″ or 1 1/2″ will do the lug 90 and 1 1/2″ or longer for the toilet flange. Re: Screws? For PVC flanges I use #14 screws 2″ long.
Can you cut stone tile without a wet saw?
One alternative to cutting stone tile with a wet saw is to make cuts using a manual hacksaw. Put on your safety glasses and use your hacksaw to slowly and carefully cut through the tile along the scored line. Use sandpaper or a sanding stone to smooth out rough edges after you’ve finished cutting through the tile.
Can you drill a tile with a normal drill bit?
As mentioned earlier, drilling through tile requires a specialist drill bit – regular or even masonry bits simply won’t do the job as they’re not strong enough to penetrate tiles’ hard surfaces. Instead, you should opt for either carbide-tipped or diamond-tipped drill bits.
