Table of Contents
How do you cut tile around a shower drain?
Cut circular drain tiles with an angle grinder. Use a tile wet saw for square or diagonal cuts. A rotary tool can be used for complicated inside-the-middle-of-a-piece type of drain cuts. Clamps may be used to hold pieces in place, such as with smaller tiles.
Should shower drain be flushed tile?
Should The Shower Drain Be Flush With The Tile? Yes, the shower floor’s drain should be flush with the tile around it at the point where the two meet. A linear drain only requires the shower floor to slope in the direction of the drain.
How do you raise the shower drain when Retiling?
Place a piece of tile next to the original drain. Position the rubber washers on top of the original drain, stacking one washer on top of the other until you raise the drain to the same height as the tile. Make sure you take into consideration the approximate 1/8 inch of grout beneath the tile when adding the washers.
Do you grout around shower drain?
Grout fills the gaps between tiles creating one surface. You can seal around the grout using regular grouting procedures and must do so to ensure the 1/4-inch space between the shower drain and the tiles creates one continuous flat surface from drain to tile.
How thick should mortar be at shower drain?
If you are installing tile, the mortar bed should be 2-3 inches thick on the outer edge and slightly less at the drain. When mixing the mortar use only enough water to obtain a “dry pack” consistency.
How do you adjust the height of a shower drain?
2″ Drain Pipe should be centered in a hole (approximately 5″ diameter) in the flooring. The top of the Pipe should be no higher than, and no more than 1/8″ lower than, the top surface of the floor on which the base will be set.
How do you install a drain extender?
Simply remove the current drain plate, place the required number of washers (if any) on top of the drain, and place the drain height extension piece over the washers. Replace the original drain screen over the extension piece and tighten with the supplied screws, and just as easy as that, you are done and ready to go.
How do you cut backer board for plumbing?
Backerboard usually contains Portland cement, so cutting it with a power tool releases dust that can irritate your eyes, skin and lungs. Cutting it with a utility knife is the best choice.
What size trowel do you use for Penny tile?
What size trowel for penny tile floor? ¼ inch x 3/16 inch V-notch trowel works well for most penny-round tiles. A 3/16 inch x 3/16 inch square notch trowel (Ditra trowel) works just as well.
What kind of Thinset do you use for Penny tile?
Most manufactures recommend putting a layer of unmodified acrylic or latex thinset between your plywood subfloor and the hardie board. It’s purpose is not adhesion, it’s to act as a filler for any gaps. Using a square notch trowel, layout a thin layer of thinset.
Should you grout or caulk around shower drain?
Instead of caulking between the tile and the drain, use the same grout you mix to use between the tiles. The grout creates a waterproof barrier that helps direct the water into the drain.
Should I grout between tile and shower base?
Grout is generally the best choice for filling joints between tiles in showers or elsewhere. Grout in these particular seams is more likely to crack due to settling. Some tile setters fill these seams with matching color caulk because it’s more flexible should movement occur.
Should you grout or caulk shower corners?
It’s essential to use caulk, not grout, in shower corners. Grout does not hold up well in corners and is prone to cracking and falling out. This is because the tiles on the two perpendicular walls expand and contract with temperature changes.
How thick can mortar be?
The building code for weight-bearing brick walls calls for mortar to be no more than 3/8 inch thick. The thickness of the mortar can vary in other types of structures from 1/8 inch to ¾ inch, according to the MC2 Estimator’s Reference website.
What kind of cement do you use to pour a shower pan?
The ideal mortar for a shower pan is a mix of standard cement mix with sand and Portland cement. This type of mortar creates a great water-resistant barrier that can support the weight of the shower unit.
How thick is thinset for shower floor?
Plan for a layer of thinset 3/16-inch to 1/8-inch thick beneath your tile. A 3/16-inch layer of thinset will be enough for tiles with a smooth back to bond the tile to the floor or backer board. For natural tiles with an uneven surface on the back, you may need to spread a 1/8-inch layer of thinset during installation.
How do you replace a tile shower drain?
Clear all of the grout around the drain. You can use a Dremel tool or a grout saw. Pry the tiles up. Be careful because you do not want to break them. Clean the drainpipe. Replace the tiles. Grout all of the gaps except the part around the drain. Seal the new drain with silicone.
Do I have to put mortar under shower pan?
If the shower base installation floor is not level, there are two options. The second is to add mortar to the floor to even it out. If sliding shims under the base does not work, opt to install the mortar bed. This is usually a good idea when floors are badly sloped or the use of shims is simply not practical.
Can showers have a one and half inch drain?
thanks. 1 1/2″ is not allowed for a shower drain by most codes but i have seen many use a 2″x1 1/2″ bushing reducer when installing a shower where a tub used to be and the pipe was neveer changed to the correct size. with a full 2″ drain the 1-2 times a year augering would probably go to once a year or less.
