Table of Contents
Can I cut baseboard on the wall?
If the baseboard is thin or made from soft wood, such as pine or cedar, you can cut it by hand. Score the baseboard carefully with a utility knife along the cut line. Once the baseboard is cut, you can use a flat bar and a hammer to tap the section you want to remove away from the wall.
What kind of saw is used to cut baseboards?
The power miter saw is the most widely used for baseboard cutting. It cuts clean miters or straight, 90-degree crosscuts with precision and little or no splintering or grain-blowout.
What angle do you cut baseboard corners?
For most DIYers, fitting baseboard moldings on the interior corners of the room is best accomplished with miter joints—45-degree miter cuts to each adjoining piece of molding. When fit together, these corners make 90-degree angles.
Can you cut baseboards with a hand saw?
You can use any type of wood, but fir or oak are the best choices. Make sure the lumber is straight, with no warps or rough edges. Keep the ends of the saw aligned with the perpendicular lines on the side of the box. Cut the baseboard you need using the box and a handsaw.
Can you use a jigsaw to cut baseboard?
While using a jigsaw to cut a baseboard corner or crown molding is rather difficult, it can be done with a high-speed jigsaw model with adjustable speed setting. It should have at least 10, if not 15 blade teeth. You need a pencil, a speed square, and a tape measure for making more precise cuts.
Do you have to cut baseboards at 45 degrees?
With inner mitered baseboard joints, each baseboard piece is cut at a 45-degree angle. When joined, the two pieces form a 90-degree angle that fits perfectly against the inside corner where two walls meet. Mitered joints work well when the walls meet at exactly 90 degrees.
How do you cut baseboards without a miter saw?
If you don’t have a miter saw, the handy circular saw is the next best alternative for ease of use and flexibility. It can handle molding joints but also other angled cuts by adjusting its angle bracket. It makes both square or straight bevel cuts on high or low baseboard widths.
What saw cuts 45 degree angle?
Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees. Saws also differ by whether the blade arm simply rotates (a basic miter saw) or both swings and slides (a sliding miter saw).
What blade is best for cutting trim?
Why Use a Fine Finish Blade? To achieve the smoothest miter saw cuts for furniture building, cabinetmaking, and trim work, you need a blade with a lot of teeth. A stock 12-inch blade typically has 32 teeth. A good trim blade commonly has 80.
How do you cut a 90 degree corner trim?
To form a 90-degree corner angle, you want to set the miter saw to 45 degrees. Using a compound miter saw, which is made specifically to cut molding, will aid in making the cut perfect. Set the molding into the miter saw upside down and backwards in order for the cut to work.
Which hand saw is best for cutting molding?
Unlike a hacksaw, coping saws are designed with the teeth pointing toward the handle. Coping saws are popular for cutting molding and baseboards. When finalizing a trim job, precision is integral for a professional result.
Do baseboards need to be mitered?
When two walls meet in an inside corner, one baseboard should be coped to fit into the other baseboard for a seamless look. You can, however, use a miter cut to join an inside corner. Use a miter saw to bevel cut the end at a 45-degree angle. The cut will reveal the profile of your baseboard.
Why are my miter cuts off?
There are few reasons your miter joint may not be lined up perfectly. Usually if you still can’t get the miter joint to close perfectly, it’s because you either cut one piece too long (or too short), or the blade itself was not perpindicular (90 degrees) from the base.
What size Mitre saw for baseboards?
Compound Miter Saws For precise cuts, a 6-inch baseboard needs to be laid flat in an 8-1/2 inch saw to slice off a partial degree. The larger 10- and 12-inch models allow the 6-inch board to rest upright against the miter fence.
What is inside corner molding?
Inside corner moldings tend to appear triangular in shape and are designed to be set into a corner such as the one underneath the countertop. An outside edge molding is typically “L” shaped and is attached to an edge to cover the original raw corner of the cabinet such as those along the bottom edge of top cabinets.
Should I nail or glue baseboards?
Installing baseboards with a combination of baseboard adhesive and finish nails creates a tight connection between the wood and the wall. The adhesive prevents the wood from bowing out between the wall studs, while the nails keep the boards locked into place while the glue sets.
How many feet of baseboards do I need?
Divide the total number of inches by 12 to convert from inches to linear feet. For example, if your wall measured 40 inches in length, and you are installing molding on the top and bottom, 40 x 2 = 80 inches. Divide 80 by 12 to get 6.66 linear feet.
