Table of Contents
Should you cut up or down with a chainsaw?
Never cut above shoulder height. Work on the uphill side of trees so they’ll roll away from you instead of over you. Use your chain brake! Whenever you aren’t cutting, the brake should be in the locked, or “On,” position.
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.
How do I cut down a large tree around my house?
When cutting large branches that may fall and damage your house, tie a rope around the branch. Then, wrap the other end around another tree trunk, at ground level. With assistance from 1 or more other workers, unwrap the rope around the tree trunk and slowly lower the large branch to the ground.
Which way will a tree fall in a storm?
A tree will most likely fall in the direction of the lean.
What side of the tree do you make the first cut?
Start Cutting Branches at the Trunk After felling the tree, cut off branches starting at the lower end of the trunk and working to the top. Whenever possible, stand on the uphill side of the tree. Work from the left side of the trunk (as you face toward the top of the tree).
Can you chainsaw upwards?
If you were to come in from the top, the blade would bind as the log is cut. When the log is supported at only one end you come in from the top and cut downwards, and the trimmed piece falls away. In any case, it is a legitimate and safe way to use a chainsaw.
Is using a chainsaw difficult?
Chainsaws are relatively easy to use once you get used to them but they are dangerous. They will cut flesh and bone as if it is not there.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Can you cut off the top of a tree without killing it?
Topping can remove half or more of a tree’s leaves. Since leaves are a tree’s food factories, losing so many can starve the tree. If the tree dies, it will have to be removed. If it survives, it likely will need corrective pruning, although it will never recover its original, natural form.
How do you cut a tree branch without killing the tree?
First, make a shallow cut on the underside of the branch, one or two inches beyond the branch collar. This will act as a barrier, preventing a bark tear if the branch falls while being cut. Second, cut through the branch two to four inches beyond the branch collar, removing the branch and leaving a stub.
Can you cut sideways with a chainsaw?
While a properly working chain saw helps you cut hours off your work time when felling trees or cutting logs for firewood, it can also be a dangerous tool when things go wrong. When a chain saw cuts sideways, it’s a clear indication that things aren’t as they should be.
Can you use a chainsaw to cut tree roots?
Both manual and chain saws can cut through roots of any size. Use a shovel to dig out the area around large roots, as the soil will clog the space between the saw teeth and make it harder to cut.
Why does my chainsaw chain get dull so fast?
With a single contact with the ground while running, a chainsaw can become very dull. This is because the ground contains sand and dust which is abrasive and contains a lot of tiny rocks. To avoid such occurrences, avoid cutting wood placed on the ground.
Should you wear gloves with chainsaw?
Always wear protective gloves when using a chainsaw. Chainsaw gloves are just one component of what you should wear when cutting wood. The other essentials are: Chainsaw chaps, protective head gear and a cut-resistant jacket.
Should I remove a tree close to house?
Trees hanging over the roof or too close to a structure might need to be removed – or at least regularly pruned. In general, large trees should be at least 20 feet away from a house or building.
How do I get rid of a tree around my house?
Cut the tree trunk in small sections starting from the top and lowering them down to the ground. The higher they are, the harder they will fall if left to fall freely. This could cause major problems if done incorrectly—including injury or property damage. Trim the stump using a chainsaw or remove the stump completely.
What is the three cut method?
Cut from the bottom, moving upward about 1/3 of the way through the branch. Next cut downward from the top of the branch several inches beyond the first cut. As the branch starts to fall, it will break away at the first cut. This prevents damage to the trunk.
