Table of Contents
Suggestions for covering exposed insulation include the following: Seal the insulation by stapling a polymembrane sheet over it. Install paneling or sheetrock over insulation located in the wall. Install plywood flooring over insulation located in the floor.
Do you have to put drywall over insulation?
Drywall is considered a suitable construction material for interior walls, but its primary purpose is not to insulate. To make a significant difference in heat flow transfer, you must include insulation along with the drywall installation.
Is it safe to leave insulation uncovered?
“Fiberglass insulation should never be left exposed in an occupied area, according to the American Lung Association,” says ALA’s Godfrey. “Exposed fiberglass insulation, once in the air, does cause respiratory reactions, such as dry, scratchy throat and coughing, as well as acting as a skin and eye irritant.
Is it OK to cover insulation with plastic?
4 Answers. Plastic isn’t recommended in this situation because it would create a second vapor barrier that can trap moisture and result in condensation and mold. Craft paper would have the same problem, this is what is most likely on the other side of the insulation for the vapor barrier you want.
How do you cover insulation in an unfinished basement ceiling?
Install 1/2-inch (or thicker) gypsum sheetrock. This works for any insulation (for spray foam and foam board, plastic sheeting is not an acceptable solution as it is not a flame-resistant material). Other options may be available, depending on your local building codes.
Can you insulate a garage without drywall?
You can also get loose-fill fiberglass, which is suitable for blowing into a garage attic space above a finished ceiling. If the walls and ceiling will remain open (not covered with drywall or plywood), it’s a good idea to use paper-faced or encapsulated fiberglass bats that are wrapped in a plastic film.
What can I cover fiberglass insulation with?
Suggestions for covering exposed insulation include the following: Seal the insulation by stapling a polymembrane sheet over it. Install paneling or sheetrock over insulation located in the wall. Install plywood flooring over insulation located in the floor.
Is it OK to breathe in insulation?
Traditional home insulation includes fiberglass, a common plastic that contains resins and fibers. As a result, people who handle or are exposed to this insulation can breathe in tiny bits of glass. After a while, those bits can get stuck in a person’s lungs, leading to respiratory ailments.
Do I need plastic over my insulation?
Without a vapor barrier in place, condensation inside the walls could ruin the insulation and promote the growth of harmful mold and bacteria. Plastic, specifically 6-mil polyethylene plastic, is the most commonly used vapor barrier.
Can you use a tarp as a vapor barrier?
Lay a heavy plastic tarp — 6 mil or thicker — over the entire area. The plastic acts as a vapor barrier, eliminating much of the migration of water vapor from the ground to the crawl space.
Do vapor barriers cause mold?
The Problem With Vapor Barriers This can lead to significant moisture problems and mold; problems occur when walls get wet during construction or more often throughout the home’s life. The increasing complexity of wall systems also fuels the issue.
Can I use plastic instead of Tyvek?
You can use plastic if you put polyethylene between your drywall and the wall studs. This way, you should get a tighter wall without trapping moisture inside the exterior walls. If you are framing out a below-grade basement, however, do not use plastic as a vapor barrier.
How can I insulate my basement cheaply?
The smart and inexpensive way to insulate joist bays is to use extruded polystyrene (XPS) foam insulation panels cut to size to fit inside the bay and “glued” in with expanding foam. When the expanding foam hardens, trim away the excess and cover the foam with a piece 1/2″ thick drywall to meet fire code.
How can I cover my basement walls cheaply?
Fortunately, you can cover basement foundation walls quickly and inexpensively. Attach wood furring strips, Z-shape channels, or 2×4 studs to flat, dry masonry walls, then add insulation and cover the strips or studs with drywall.
What is the easiest way to cover a basement ceiling?
A super easy DIY option for your basement ceiling is glue-on tiles. Typically made of polystyrene or fiberboard, these tiles come in a variety of colors, sizes, and styles, and are also paintable. You’ll need to install a foundation, like plywood, to glue them to. But after that, it’s as simple as glue and stick.
What can I use instead of drywall in garage?
Alternatives to Drywall for Garage Walls Sturdy Wood Sheathing. Wood sheathing, such as plywood or oriented strandboard (OSB), represents a simple yet economical finish option for garage walls. Stylish Metal Panels. Low-Maintenance Plastic. Practical Storage Panels. Solid Cement Board. Consider Fire Codes First.
How can I insulate my garage cheaply?
Fiberglass roll insulation is the cheapest and easiest type to install, provided that your garage’s interior walls have not been constructed. Unroll the insulation between the wall studs with the vapor barrier facing the inside of the garage.
What can you use instead of drywall?
Drywall Alternatives Wood Planks. Wood planks are an age-old drywall alternative that has certainly stood the test of time well. Veneer Plaster. Lath & Plaster. Plywood and Sheet Wood. Texture Wall Panels. Brick & Masonry. Exposed Concrete Block. Cement Board.
