Table of Contents
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
What should deck stair stringers rest on?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.
Do stair stringers need hangers?
To attach stair stringers to a deck, you must use a metal stair stringer hanger. End-nailing, toe-nailing, or screwing stringers to a header is not allowed per the International Residential Code. Metal hangers must use appropriately sized nails or fasteners specific to the stringer hanger manufacturer.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
Do you install risers or treads first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser.
How far should stair stringers be apart?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
How do you reinforce stair stringers?
One of the easiest methods of reinforcing your wood stair stringers is using 2×12 skirt boards along the outsides of your stairs. A skirt board is pretty much what it sounds like; triangular shaped wood that goes along the sides of your stair and hides all of the unsightly notched stringers and hardware.
How do I anchor my deck stairs to the ground?
How to Anchor Deck Stairs to Concrete Use your jigsaw. Notch out the bottom front of the center stair stringers to accept a 2×4 base plate. Make sure your stringers are level. Fasten the base plate to the stair stringers with screws. Locked in place.
Can you use joist hangers for stringers?
This metal bracket supports the stringer and holds it on the framing. Stringer hangers look like joist hangers and function in the same way. Most local code authorities require the use of stringer hangers, and using them makes installation easier.
Do deck stair stringers need support?
To help resist both vertical and lateral loads, stringers require proper support and attachment at these bearing points. Without proper support, vertical loads (gravity) can pull the stringers down from their bearing points, while lateral (horizontal) loads can pull the stringers away from their bearing points.
Do deck stairs need risers?
Most high-end deck projects use closed risers to finish the stairs. They also are often in violation of IRC code for decks over 30″, which maintains that they meet the same requirements as guardrail infill. Stair risers may not have openings present that would allow a 4” diameter sphere to pass through.
Can I use 2×10 for deck stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
What size lumber do you use for stair risers?
Stair stringers are cut from 2×12 lumber. For exposed side stringers, use cedar lumber. Make one stringer for each 16 inches of stair width. Allow for light boxes if riser lights will be installed.
What size lumber are stair stringers cut from?
Selecting stringer stock Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible.
How far should a tread overhang the riser?
Stairs must have an overhang between 3/4″ to 1-1/4” to increase the depth of the step, making it better for descent while maintaining a clear 10-inch going for the ascent. Treads that are 11-inches deep or greater do not require an overhang.
Should you nail or screw stair treads?
Don’t fasten treads and or risers with only nails or staples. The adhesive is much more important than the fasteners. There will be times when fastening may be limited, so a good adhesive is critical. Rely on the front edge of the riser for your level surface.
Can I just glue stair treads?
Treads should be attached with a combination of adhesive and nails. Nail length being a minimum of twice the thickness of your tread and of 16 gauge or larger. You can just glue the risers but that’s not something I’d personally do either. I’d use adhesive and a few Brad nails ( 18 gauge ) will suffice.
How many stringers do I need for 36 inch deck stairs?
Because of this, you should never space your stair stringers more than 16” on center. This means you will need to install a minimum of four stringers on any stairway wider than 36”. Always check the maximum span for your decking material as it applies to stair treads.
How many steps do I need for my deck?
To determine the rise and run of the steps, measure the distance from the floor of the deck to the ground and divide that number by 7.5. The result will be the number of steps the staircase will need (e.g., deck is 112″ from the ground; 112/7.5 = 14.93. Round up to get 15 steps).
How many stringers do I need for my deck stairs?
How do I calculate a stair stringer? Start by finding the overall height that the staircase will be. Decide the height or “rise” you’ll want for each step. Divide the total height of the staircase by the height or “rise” you want for each step.
How many steps is 4 foot rise?
A four-foot high deck can have a range between 6 and 8 steps.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
