Table of Contents
Scrub the floor with trisodium phosphate (TSP) or a similar strong alkaline cleaner-degreaser and rinse with a hose. While the floor is still wet, sprinkle it with muriatic or phosphoric acid and scrub with a stiff-bristled nylon brush for a minute or so.
How do you clean an unfinished basement?
Clean regularly to keep away the cobwebs and dust bunnies. Dust (using a broom with a rag on the end to reach into the rafters), vacuum, and mop. Managing mildew and mold will improve the smell of the basement. Using a dehumidifier, especially in the summer, can help.
How do you clean a basement floor after construction?
First, sprinkle little water over the floor. Then, you should sweep and dust the room. If you find big-sized debris, you can handpick them before vacuuming or sweeping. Go over the floor again and sweep the floor, removing any loose dust particles and small size debris.
How do you clean sealed concrete floors indoors?
To clean a sealed concrete floor, sweep or vacuum the surface to remove any loose dirt and then mop using a dust mop to get rid of fine dust. Mop the floor with warm water mixed with dish soap and then rinse off using a clean mop and fresh, clean water.
How do you clean an unsealed concrete basement floor?
How to Clean Unsealed Concrete Floors Sprinkle sawdust on grease and oil stains. Sweep the floor with a push broom. Dust mop or vacuum the floor. Apply detergent and water on the stains. Scrub the stained spots with a brush. Mop with a baking soda solution. Rinse and wipe the floor dry.
How do you clean a basement floor with no drain?
Mix a quarter cup of ammonia, a few squirts of dish soap, and water in a bucket. Use a nylon scrub brush with stiff bristles to scrub the cleaning solution onto the concrete floor.
How do you clean unfinished concrete floors?
How to Clean an Unsealed Concrete Floor Sprinkle sawdust or cat litter over any oil or grease spots on the concrete. Sweep all debris from the concrete floor with a push broom. Sprinkle powdered dishwasher detergent on the stain. Pour boiling water over the detergent after soaking.
How do you clean a dirty concrete floor?
How to Clean Concrete Floors Clear debris. Clean and clear the floor of all debris, dirt and dust using a vacuum, soft bristle broom or dry dust mop. Apply Simple Green Multi-Surface Floor Care. Spray the cleaning solution as a light mist across your floor section by section. Mop up in sections. Dry.
How do you clean dirt off a basement floor?
Mop concrete floor and walls with a bleach solution (3/4 cups of household bleach to a gallon of water.) Rinse and dry after 5 minutes. Open windows when applying the bleach solution.
How do you clean a basement concrete floor?
For general cleaning needs, you can combine a cup of ammonia with liquid detergent in a bucket of hot water. Then, use a stiff-bristle brush to scrub the floor with your cleaning mixture. Do not use a brush with metal bristles or fibers because the metal shavings can get stuck in the concrete pores.
Can you mop a concrete basement floor?
Use a rubber brush or a mop to apply the bleach solution to the floor, scrubbing it as you go. After allowing the solution to sit for ten minutes, mop the floor with clean water to rinse the bleach. Allow the floor to dry completely before closing ventilation avenues and using the space again.
What is the best cleaner for sealed concrete floors?
Don’t use ammonia, bleach or any highly acidic substance on polished or stamped floors. Some good cleaners include Castile soap, liquid dish detergent, stone cleaners and mild floor cleaners. Mix a solution, apply to floor with a wet mop and then rinse with a mop dipped in clean water.
What does vinegar do to concrete?
Etching – Vinegar’s ability to dissolve CaCO3 will dull your marble, travertine, concrete and terrazzo surfaces. It may “clean” the surface but it is also dissolving pits into the finish and effectively dulling it. This will affect marble, travertine, concrete and concrete terrazzo surfaces.
Is it OK to use bleach on concrete?
Concrete floors are commonly used in basements, patios and garages. Since these areas are prone to dirt, residue, mold or mildew, you should clean them with bleach. Bleach effectively removes many stains, deodorizes and kills mold and mildew when used properly. Allow the bleach solution to sit for five minutes.
Can you use Pine Sol on cement?
Don’t: Never use everyday floor cleaning products, such as Pine-Sol; always select a pH-neutral cleaner. Never use products such as ammonia, vinegar, bleach, muriatic acid, or other harsh cleaners on concrete floors.
Can you pressure wash a basement floor?
Pressure washing is the way to go when you have large surfaces to clean. Ideal for hard, non-porous surfaces like concrete floors and walls, pressure washers can clean up your basement a lot faster than using a sponge and some water.
How do I clean my concrete basement floor after sewer backup?
How do I clean up after floods and sewer backups? Odors from sewage backups are unpleasant but not harmful. Wash contaminated surfaces/objects with warm, soapy water and disinfect with a bleach/water solution, one cap of 5.25 percent chlorine bleach per one gallon water.
Can you use vinegar to clean concrete floors?
White vinegar and a little scrubbing with a brush is a very effective, eco-friendly way to remove rust stains from concrete—even those that are decades old. Pour the white vinegar directly onto the stain, allow the liquid to penetrate the area for 20 minutes, and scrub with a stiff-bristled brush.
